Remember this version support Windows system users only. App online version of 350-401 Reliable Exam Cram Sheet File exam questions is suitable to all kinds of equipment or digital devices and supportive to offline exercise on the condition that you practice it without mobile data. Our PDF version of 350-401 Reliable Exam Cram Sheet File training materials is legible to read and remember, and support printing request. Whenever it is possible, you can begin your study as long as there has a computer. In addition, all installed 350-401 Reliable Exam Cram Sheet File study tool can be used normally. Get the test 350-401 Reliable Exam Cram Sheet File certification is not achieved overnight, we need to invest a lot of time and energy to review, and the review process is less a week or two, more than a month or two, or even half a year, so 350-401 Reliable Exam Cram Sheet File exam questions are one of the biggest advantage is that it is the most effective tools for saving time for users.
CCNP Enterprise 350-401 Within a year, we provide free updates.
CCNP Enterprise 350-401 Reliable Exam Cram Sheet File - Implementing Cisco Enterprise Network Core Technologies (350-401 ENCOR) As a responsible company over ten years, we are trustworthy. After you use, you will know that it is really good. The site of Omgzlook is well-known on a global scale.
The world today is in an era dominated by knowledge. Knowledge is the most precious asset of a person. If you feel exam is a headache, don't worry.
Cisco 350-401 Reliable Exam Cram Sheet File - So that you can achieve a multiplier effect.
Our 350-401 Reliable Exam Cram Sheet File guide question dumps are suitable for all age groups. Even if you have no basic knowledge about the relevant knowledge, you still can pass the 350-401 Reliable Exam Cram Sheet File exam. We sincerely encourage you to challenge yourself as long as you have the determination to study new knowledge. Our 350-401 Reliable Exam Cram Sheet File exam material is full of useful knowledge, which can strengthen your capacity for work. As we all know, it is important to work efficiently. So once you have done you work excellently, you will soon get promotion. You need to be responsible for your career development. The assistance of our 350-401 Reliable Exam Cram Sheet File guide question dumps are beyond your imagination. You will regret if you throw away the good products.
Do not feel that you have no ability, and don't doubt yourself. When you choose to participate in the Cisco 350-401 Reliable Exam Cram Sheet File exam, it is necessary to pass it.
350-401 PDF DEMO:
QUESTION NO: 1
Which technology provides a secure communication channel for all traffic at Layer 2 of the OSI model?
A. IPsec
B. Cisco Trustsec
C. MACsec
D. SSL
Answer: C
Explanation:
MACsec, defined in 802.1AE, provides MAC-layer encryption over wired networks by using out- of
-band methods for encryption keying. The MACsec Key Agreement (MKA) Protocol provides the required session keys and manages the required encryption keys. MKA and MACsec are implemented after successful authentication using the 802.1x Extensible Authentication Protocol (EAP-TLS) or Pre
Shared Key (PSK) framework.
A switch using MACsec accepts either MACsec or non-MACsec frames, depending on the policy associated with the MKA peer. MACsec frames are encrypted and protected with an integrity check value (ICV). When the switch receives frames from the MKA peer, it decrypts them and calculates the correct ICV by using session keys provided by MKA. The switch compares that ICV to the ICV within the frame. If they are not identical, the frame is dropped. The switch also encrypts and adds an ICV to any frames sent over the secured port (the access point used to provide the secure MAC service to a
MKA peer) using the current session key.
Reference: https://www.cisco.com/c/en/us/td/docs/switches/lan/catalyst9300/software/release/16-
9/configuration_guide/sec/b_169_sec_9300_cg/macsec_encryption.html
Note: Cisco Trustsec is the solution which includes MACsec.
QUESTION NO: 2
Refer to the exhibit. A port channel is configured between SW2 and SW3. SW2 is not running a
Cisco operating system. When all physical connections are mode, the port channel does not establish.
Based on the configuration excerpt of SW3, what is the cause of the problem?
A. The port-channel interface lead balance should be set to src-mac
B. The port-channel trunk is not allowing the native VLAN.
C. The port-channel should be set to auto.
D. The port channel on SW2 is using an incompatible protocol.
Answer: D
Explanation:
The Cisco switch was configured with PAgP, which is a Cisco proprietary protocol so non-Cisco switch could not communicate.
QUESTION NO: 3
To increase total throughput and redundancy on the links between the wireless controller and switch, the customer enabled LAG on the wireless controller.
Which EtherChannel mode must be configured on the switch to allow the WLC to connect?
A. Active
B. On
C. Auto
D. Passive
Answer: B
Explanation:
Restrictions for Link Aggregation:
You can bundle all eight ports on a Cisco 5508 Controller into a single link.
Terminating on two different modules within a single Catalyst 6500 series switch provides redundancy and ensures that connectivity between the switch and the controller is maintained when one module fails. The controller's port 1 is connected to Gigabit interface 3/1, and the controller's port 2 is connected to Gigabit interface 2/1 on the Catalyst 6500 series switch. Both switch ports are assigned to the same channel group.
LAG requires the EtherChannel to be configured for 'mode on' on both the controller and the Catalyst switch.
Once the EtherChannel is configured as on at both ends of the link, the Catalyst switch should not be configured for either Link Aggregation Control Protocol (LACP) or Cisco proprietary Port Aggregation
Protocol (PAgP) but be set unconditionally to LAG. Because no channel negotiation is done between the controller and the switch, the controller does not answer to negotiation frames and the LAG is not formed if a dynamic form of LAG is set on the switch. Additionally, LACP and PAgP are not supported on the controller.
If the recommended load-balancing method cannot be configured on the Catalyst switch, then configure the LAG connection as a single member link or disable LAG on the controller.
https://www.cisco.com/c/en/us/td/docs/wireless/controller/7-5/configuration- guide/b_cg75/b_cg75_chapter_0100010.html
QUESTION NO: 4
Which statement about multicast RPs is true?
A. RPs are required for protocol independent multicast sparse mode and dense mode.
B. By default, the RP is needed only to start new sessions with sources and receivers.
C. By default, the RP is needed periodically to maintain sessions with sources and receivers
D. RPs are required only when using protocol independent multicast dense mode.
Answer: B
Explanation:
A rendezvous point (RP) is required only in networks running Protocol Independent Multicast sparse mode (PIM-SM).
By default, the RP is needed only to start new sessions with sources and receivers.
Reference:
https://www.cisco.com/c/en/us/td/docs/ios/solutions_docs/ip_multicast/White_papers/rps.html
For your information, in PIM-SM, only network segments with active receivers that have explicitly requested multicast data will be forwarded the traffic. This method of delivering multicast data is in contrast to the PIM dense mode (PIM-DM) model. In PIM-DM, multicast traffic is initially flooded to all segments of the network. Routers that have no downstream neighbors or directly connected receivers prune back the unwanted traffic.
QUESTION NO: 5
What is the difference between a RIB and a FIB?
A. The FIB is populated based on RIB content
B. The RIB is used to make IP source prefix-based switching decisions
C. The RIB maintains a mirror image of the FIB
D. The FIB is where all IP routing information is stored
Answer: A
Explanation:
CEF uses a Forwarding Information Base (FIB) to make IP destination prefix-based switching decisions.
The FIB is conceptually similar to a routing table or information base. It maintains a mirror image of the forwarding information contained in the IP routing table. When routing or topology changes occur in the network, the IP routing table is updated, and those changes are reflected in the FIB. The
FIB maintains next-hop address information based on the information in the IP routing table. Because there is a one-to-one correlation between FIB entries and routing table entries, the FIB contains all known routes and eliminates the need for route cache maintenance that is associated with earlier switching paths such as fast switching and optimum switching.
Note: In order to view the Routing information base (RIB) table, use the "show ip route" command.
To view the Forwarding Information Base (FIB), use the "show ip cef" command. RIB is in Control plane while FIB is in Data plane.
Please be assured that with the help of EMC D-PDM-DY-23 learning materials, you will be able to successfully pass the exam. And then, to take Cisco SAP C-THR96-2405 exam can help you to express your desire. If you happen to be facing this problem, you should choose our HP HPE2-T37 real exam. After you use Omgzlook Cisco HP HP2-I57 study guide, you not only can pass the exam at the first attempt, also can master the skills the exam demands. If you have problems with your installation or use on our SAP C-THR86-2405 training guide, our 24 - hour online customer service will resolve your trouble in a timely manner.
Updated: May 28, 2022