If you don’t have enough ability, it is very possible for you to be washed out. On the contrary, the combination of experience and the 350-401 Questions certification could help you resume stand out in a competitive job market. As the quick development of the world economy and intense competition in the international, the world labor market presents many new trends: company’s demand for the excellent people is growing. Do you wonder why so many peers can successfully pass 350-401 Questions exam? Are also you eager to obtain 350-401 Questions exam certification? Now I tell you that the key that they successfully pass the exam is owing to using our 350-401 Questions exam software provided by our Omgzlook. Our 350-401 Questions exam software offers comprehensive and diverse questions, professional answer analysis and one-year free update service after successful payment; with the help of our 350-401 Questions exam software, you can improve your study ability to obtain 350-401 Questions exam certification. Our 350-401 Questions training materials are compiled carefully with correct understanding of academic knowledge using the fewest words to express the most clear ideas, rather than unnecessary words expressions or sentences and try to avoid out-of-date words.
CCNP Enterprise 350-401 We provide one-year customer service; 4.
And most of all, you will get reward by our 350-401 - Implementing Cisco Enterprise Network Core Technologies (350-401 ENCOR) Questions training engine in the least time with little effort. If you are urgent to pass exam our exam materials will be suitable for you. Mostly you just need to remember the questions and answers of our Cisco Valid Test 350-401 Experience exam review questions and you will clear exams.
There is no doubt that the certification has become more and more important for a lot of people, especial these people who are looking for a good job, and it has been a general trend. More and more workers have to spend a lot of time on meeting the challenge of gaining the 350-401 Questions certification by sitting for an exam. It is known to us that more and more companies start to pay high attention to the 350-401 Questions certification of the candidates.
Cisco 350-401 Questions - So stop hesitation and buy our study materials.
Preparing for the 350-401 Questions real exam is easier if you can select the right test questions and be sure of the answers. The 350-401 Questions test answers are tested and approved by our certified experts and you can check the accuracy of our questions from our free demo. Expert for one-year free updating of 350-401 Questions dumps pdf, we promise you full refund if you failed exam with our dumps.
So you just need to memorize our correct questions and answers of the 350-401 Questions study materials. You absolutely can pass the exam.
350-401 PDF DEMO:
QUESTION NO: 1
What is the difference between a RIB and a FIB?
A. The FIB is populated based on RIB content
B. The RIB is used to make IP source prefix-based switching decisions
C. The RIB maintains a mirror image of the FIB
D. The FIB is where all IP routing information is stored
Answer: A
Explanation:
CEF uses a Forwarding Information Base (FIB) to make IP destination prefix-based switching decisions.
The FIB is conceptually similar to a routing table or information base. It maintains a mirror image of the forwarding information contained in the IP routing table. When routing or topology changes occur in the network, the IP routing table is updated, and those changes are reflected in the FIB. The
FIB maintains next-hop address information based on the information in the IP routing table. Because there is a one-to-one correlation between FIB entries and routing table entries, the FIB contains all known routes and eliminates the need for route cache maintenance that is associated with earlier switching paths such as fast switching and optimum switching.
Note: In order to view the Routing information base (RIB) table, use the "show ip route" command.
To view the Forwarding Information Base (FIB), use the "show ip cef" command. RIB is in Control plane while FIB is in Data plane.
QUESTION NO: 2
Which feature does Cisco TrustSec use to provide scalable, secure communication throughout a network?
A. security group tag number assigned to each user on a switch
B. security group tag ACL assigned to each router on a network
C. security group tag ACL assigned to each port on a switch
D. security group tag number assigned to each port on a network
Answer: D
Explanation:
Cisco TrustSec uses tags to represent logical group privilege. This tag, called a Security Group Tag
(SGT), is used in access policies. The SGT is understood and is used to enforce traffic by Cisco switches, routers and firewalls . Cisco TrustSec is defined in three phases: classification, propagation and enforcement.
When users and devices connect to a network, the network assigns a specific security group.
This process is called classification. Classification can be based on the results of the authentication or by associating the SGT with an IP, VLAN, or port-profile (-> Answer A and answer C are not correct as they say "assigned ... on a switch" only. Answer D is not correct either as it says "assigned to each router").
QUESTION NO: 3
To increase total throughput and redundancy on the links between the wireless controller and switch, the customer enabled LAG on the wireless controller.
Which EtherChannel mode must be configured on the switch to allow the WLC to connect?
A. Active
B. On
C. Auto
D. Passive
Answer: B
Explanation:
Restrictions for Link Aggregation:
You can bundle all eight ports on a Cisco 5508 Controller into a single link.
Terminating on two different modules within a single Catalyst 6500 series switch provides redundancy and ensures that connectivity between the switch and the controller is maintained when one module fails. The controller's port 1 is connected to Gigabit interface 3/1, and the controller's port 2 is connected to Gigabit interface 2/1 on the Catalyst 6500 series switch. Both switch ports are assigned to the same channel group.
LAG requires the EtherChannel to be configured for 'mode on' on both the controller and the Catalyst switch.
Once the EtherChannel is configured as on at both ends of the link, the Catalyst switch should not be configured for either Link Aggregation Control Protocol (LACP) or Cisco proprietary Port Aggregation
Protocol (PAgP) but be set unconditionally to LAG. Because no channel negotiation is done between the controller and the switch, the controller does not answer to negotiation frames and the LAG is not formed if a dynamic form of LAG is set on the switch. Additionally, LACP and PAgP are not supported on the controller.
If the recommended load-balancing method cannot be configured on the Catalyst switch, then configure the LAG connection as a single member link or disable LAG on the controller.
https://www.cisco.com/c/en/us/td/docs/wireless/controller/7-5/configuration- guide/b_cg75/b_cg75_chapter_0100010.html
QUESTION NO: 4
Which technology provides a secure communication channel for all traffic at Layer 2 of the OSI model?
A. IPsec
B. Cisco Trustsec
C. MACsec
D. SSL
Answer: C
Explanation:
MACsec, defined in 802.1AE, provides MAC-layer encryption over wired networks by using out- of
-band methods for encryption keying. The MACsec Key Agreement (MKA) Protocol provides the required session keys and manages the required encryption keys. MKA and MACsec are implemented after successful authentication using the 802.1x Extensible Authentication Protocol (EAP-TLS) or Pre
Shared Key (PSK) framework.
A switch using MACsec accepts either MACsec or non-MACsec frames, depending on the policy associated with the MKA peer. MACsec frames are encrypted and protected with an integrity check value (ICV). When the switch receives frames from the MKA peer, it decrypts them and calculates the correct ICV by using session keys provided by MKA. The switch compares that ICV to the ICV within the frame. If they are not identical, the frame is dropped. The switch also encrypts and adds an ICV to any frames sent over the secured port (the access point used to provide the secure MAC service to a
MKA peer) using the current session key.
Reference: https://www.cisco.com/c/en/us/td/docs/switches/lan/catalyst9300/software/release/16-
9/configuration_guide/sec/b_169_sec_9300_cg/macsec_encryption.html
Note: Cisco Trustsec is the solution which includes MACsec.
QUESTION NO: 5
Refer to the exhibit. A port channel is configured between SW2 and SW3. SW2 is not running a
Cisco operating system. When all physical connections are mode, the port channel does not establish.
Based on the configuration excerpt of SW3, what is the cause of the problem?
A. The port-channel interface lead balance should be set to src-mac
B. The port-channel trunk is not allowing the native VLAN.
C. The port-channel should be set to auto.
D. The port channel on SW2 is using an incompatible protocol.
Answer: D
Explanation:
The Cisco switch was configured with PAgP, which is a Cisco proprietary protocol so non-Cisco switch could not communicate.
Our website offers you the most comprehensive Fortinet NSE7_SDW-7.2 study guide for the actual test and the best quality service for aftersales. Huawei H13-527_V5.0 - You can take advantage of the certification. For most busy IT workers, SAP C-BW4H-214 dumps pdf is the best alternative to your time and money to secure the way of success in the IT filed. Our CyberArk CPC-SEN study materials allow you to improve your competitiveness in a short period of time. You can find latest AAPC CPC test answers and questions in our pass guide and the detailed explanations will help you understand the content easier.
Updated: May 28, 2022