And our 200-301 Reliable Test Questions Explanations training questions are popular in the market. We believe you will make the right choice. Our 200-301 Reliable Test Questions Explanations exam materials are formally designed for the exam. So, please give the 200-301 Reliable Test Questions Explanations study materials a chance to help you. Though our 200-301 Reliable Test Questions Explanations training guide is proved to have high pass rate, but If you try our 200-301 Reliable Test Questions Explanations exam questions but fail in the final exam, we can refund the fees in full only if you provide us with a transcript or other proof that you failed the exam. According to your actual need, you can choose the version for yourself which is most suitable for you to preparing for the coming exam.
CCNA 200-301 I wish you good luck.
CCNA 200-301 Reliable Test Questions Explanations - Cisco Certified Network Associate Exam You can download the part of the trial exam questions and answers as a try. Cisco High 200-301 Passing Score is a very important certification exam in the IT industry and passing Cisco certification High 200-301 Passing Score exam is very difficult. But in order to let the job position to improve spending some money to choose a good training institution to help you pass the exam is worthful.
There are many dumps and training materials providers that would guarantee you pass the Cisco 200-301 Reliable Test Questions Explanations exam. Omgzlook speak with the facts, the moment when the miracle occurs can prove every word we said. The exam materiala of the Omgzlook Cisco 200-301 Reliable Test Questions Explanations is specifically designed for candicates.
Cisco 200-301 Reliable Test Questions Explanations - Select it will be your best choice.
Cisco 200-301 Reliable Test Questions Explanations certification exam is among those popular IT certifications. It is also the dream of ambitious IT professionals. This part of the candidates need to be fully prepared to allow them to get the highest score in the 200-301 Reliable Test Questions Explanations exam, make their own configuration files compatible with market demand.
If you won't believe us, you can visit our Omgzlook to experience it. And then, I am sure you must choose Omgzlook exam dumps.
200-301 PDF DEMO:
QUESTION NO: 1
Which two tasks must be performed to configure NTP to a trusted server in client mode on a single network device? (Choose two)
A. Verify the time zone.
B. Disable NTP broadcasts
C. Set the NTP server private key
D. Specify the IP address of the NTP server
E. Enable NTP authentication.
Answer: D,E
Explanation:
To configure authentication, perform this task in privileged mode:
Step 1: Configure an authentication key pair for NTP and specify whether the key will be trusted or untrusted.
Step 2: Set the IP address of the NTP server and the public key.
Step 3: Enable NTP client mode.
Step 4: Enable NTP authentication.
Step 5: Verify the NTP configuration.
Reference: https://www.cisco.com/c/en/us/td/docs/switches/lan/catalyst4000/8-
2glx/configuration/guide/ ntp.html
QUESTION NO: 2
Drag and Drop Question
Drag and drop the WLAN components from the left onto the correct descriptions on the right.
Answer:
Explanation:
The service port can be used management purposes, primarily for out-of-band management.
However, AP management traffic is not possible across the service port. In most cases, the service port is used as a "last resort" means of accessing the controller GUI for management purposes. For example, in the case where the system distribution ports on the controller are down or their communication to the wired network is otherwise degraded.
A dynamic interface with the Dynamic AP Management option enabled is used as the tunnel source for packets from the controller to the access point and as the destination for CAPWAP packets from the access point to the controller.
The virtual interface is used to support mobility management, Dynamic Host Configuration Protocol
(DHCP) relay, and embedded Layer 3 security such as guest web authentication. It also maintains the
DNS gateway host name used by Layer 3 security and mobility managers to verify the source of certificates when Layer 3 web authorization is enabled.
Reference: https://www.cisco.com/c/en/us/td/docs/wireless/controller/8-5/config- guide/b_cg85/ports_and_interfaces.html
QUESTION NO: 3
Refer to the exhibit. After you apply the given configuration to arouter, the DHCP clients behind the device connot communicate with hosts outside of their subnet.
Which action is most likely to correct the problem?
A. configure the default gateway
B. Configure the dns server on the same subnet as the clients
C. Activate the dhcp pool
D. Correct the subnet mask
Answer: A
QUESTION NO: 4
Which statement about Link Aggregation when implemented on a Cisco Wireless LAN
Controller is true?
A. One functional physical port is needed to pass client traffic
B. The EtherChannel must be configured in "mode active"
C. When enabled the WLC bandwidth drops to 500 Mbps
D. To pass client traffic two or more ports must be configured.
Answer: A
Explanation:
Link aggregation (LAG) is a partial implementation of the 802.3ad port aggregation standard. It bundles all of the controller's distribution system ports into a single 802.3ad port channel.
Restriction for Link aggregation:
- LAG requires the EtherChannel to be configured for `mode on' on both the controller and the
Catalyst switch -> Answer B is not correct.
- If the recommended load-balancing method cannot be configured on the Catalyst switch, then configure the LAG connection as a single member link or disable LAG on the controller -> Answer A is not correct while answer D is correct.
Reference: https://www.cisco.com/c/en/us/td/docs/wireless/controller/7-5/configuration- guide/b_cg75/ b_cg75_chapter_0100010.html
QUESTION NO: 5
Refer to the exhibit. C-router is to be used as a "router-on-a-stick" to route between the
VLANs.
All the interfaces have been properly configured and IP routing is operational. The hosts in the VLANs have been configured with the appropriate default gateway.
What is true about this configuration?
A. These commands need to be added to the configuration:
C-router(config)# router rip
C-router(config-router)# network 172.19.0.0
B. These commands need to be added to the configuration:
C-router(config)# router ospf 1
C-router(config-router)# network 172.19.0.0 0.0.3.255 area 0
C. These commands need to be added to the configuration:
C-router(config)# router eigrp 123
C-router(config-router)# network 172.19.0.0
D. No further routing configuration is required.
Answer: D
Explanation:
Since all the same router (C-router) is the default gateway for all three VLANs, all traffic destined to a different VLAN will be sent to the C-router. The C-router will have knowledge of all three networks since they will appear as directly connected in the routing table. Since the C-router already knows how to get to all three networks, no routing protocols need to be configured.
Salesforce PDX-101 - In Omgzlook you can find your treasure house of knowledge. Would you like to attend Cisco PRINCE2 PRINCE2-Foundation certification exam? Certainly a lot of people around you attend this exam. IBM S1000-007 - We absolutely protect the interests of consumers. SAP C-THR70-2404 - Whether to pass the exam successfully, it consists not in how many materials you have seen, but in if you find the right method. Cisco 200-201 - The coverage of the products of Omgzlook is very broad.
Updated: May 28, 2022