Next, I will detail the relevant information of our learning materials so that you can have a better understanding of our 350-401 Valid Exam Online guide training. Our 350-401 Valid Exam Online study tool prepared by our company has now been selected as the secret weapons of customers who wish to pass the exam and obtain relevant certification. If you are agonizing about how to pass the exam and to get the Cisco certificate, now you can try our learning materials. The client only need to spare 1-2 hours to learn our Implementing Cisco Enterprise Network Core Technologies (350-401 ENCOR) study question each day or learn them in the weekends. Commonly speaking, people like the in-service staff or the students are busy and don’t have enough time to prepare the exam. After your purchase of 350-401 Valid Exam Online learning engine, our system will send a link to your email in 5 to 10 minutes.
CCNP Enterprise 350-401 So your error can be corrected quickly.
CCNP Enterprise 350-401 Valid Exam Online - Implementing Cisco Enterprise Network Core Technologies (350-401 ENCOR) We hope to grow with you and help you get more success in your life. Many students often complain that they cannot purchase counseling materials suitable for themselves. A lot of that stuff was thrown away as soon as it came back.
Our passing rate may be the most attractive factor for you. Our 350-401 Valid Exam Online learning guide have a 99% pass rate. This shows what? As long as you use our products, you can pass the exam!
Cisco 350-401 Valid Exam Online - So, buy our products immediately!
We offer free demos of the 350-401 Valid Exam Online exam braindumps for your reference before you pay for them, for there are three versions of the 350-401 Valid Exam Online practice engine so that we also have three versions of the free demos. And we will send you the new updates if our experts make them freely. On condition that you fail the exam after using our 350-401 Valid Exam Online study guide unfortunately, we will switch other versions for you or give back full of your refund. All we do and the promises made are in your perspective.
They have rich experience in predicating the 350-401 Valid Exam Online exam. Then you are advised to purchase the study materials on our websites.
350-401 PDF DEMO:
QUESTION NO: 1
To increase total throughput and redundancy on the links between the wireless controller and switch, the customer enabled LAG on the wireless controller.
Which EtherChannel mode must be configured on the switch to allow the WLC to connect?
A. Active
B. On
C. Auto
D. Passive
Answer: B
Explanation:
Restrictions for Link Aggregation:
You can bundle all eight ports on a Cisco 5508 Controller into a single link.
Terminating on two different modules within a single Catalyst 6500 series switch provides redundancy and ensures that connectivity between the switch and the controller is maintained when one module fails. The controller's port 1 is connected to Gigabit interface 3/1, and the controller's port 2 is connected to Gigabit interface 2/1 on the Catalyst 6500 series switch. Both switch ports are assigned to the same channel group.
LAG requires the EtherChannel to be configured for 'mode on' on both the controller and the Catalyst switch.
Once the EtherChannel is configured as on at both ends of the link, the Catalyst switch should not be configured for either Link Aggregation Control Protocol (LACP) or Cisco proprietary Port Aggregation
Protocol (PAgP) but be set unconditionally to LAG. Because no channel negotiation is done between the controller and the switch, the controller does not answer to negotiation frames and the LAG is not formed if a dynamic form of LAG is set on the switch. Additionally, LACP and PAgP are not supported on the controller.
If the recommended load-balancing method cannot be configured on the Catalyst switch, then configure the LAG connection as a single member link or disable LAG on the controller.
https://www.cisco.com/c/en/us/td/docs/wireless/controller/7-5/configuration- guide/b_cg75/b_cg75_chapter_0100010.html
QUESTION NO: 2
Which technology provides a secure communication channel for all traffic at Layer 2 of the OSI model?
A. IPsec
B. Cisco Trustsec
C. MACsec
D. SSL
Answer: C
Explanation:
MACsec, defined in 802.1AE, provides MAC-layer encryption over wired networks by using out- of
-band methods for encryption keying. The MACsec Key Agreement (MKA) Protocol provides the required session keys and manages the required encryption keys. MKA and MACsec are implemented after successful authentication using the 802.1x Extensible Authentication Protocol (EAP-TLS) or Pre
Shared Key (PSK) framework.
A switch using MACsec accepts either MACsec or non-MACsec frames, depending on the policy associated with the MKA peer. MACsec frames are encrypted and protected with an integrity check value (ICV). When the switch receives frames from the MKA peer, it decrypts them and calculates the correct ICV by using session keys provided by MKA. The switch compares that ICV to the ICV within the frame. If they are not identical, the frame is dropped. The switch also encrypts and adds an ICV to any frames sent over the secured port (the access point used to provide the secure MAC service to a
MKA peer) using the current session key.
Reference: https://www.cisco.com/c/en/us/td/docs/switches/lan/catalyst9300/software/release/16-
9/configuration_guide/sec/b_169_sec_9300_cg/macsec_encryption.html
Note: Cisco Trustsec is the solution which includes MACsec.
QUESTION NO: 3
What is the difference between a RIB and a FIB?
A. The FIB is populated based on RIB content
B. The RIB is used to make IP source prefix-based switching decisions
C. The RIB maintains a mirror image of the FIB
D. The FIB is where all IP routing information is stored
Answer: A
Explanation:
CEF uses a Forwarding Information Base (FIB) to make IP destination prefix-based switching decisions.
The FIB is conceptually similar to a routing table or information base. It maintains a mirror image of the forwarding information contained in the IP routing table. When routing or topology changes occur in the network, the IP routing table is updated, and those changes are reflected in the FIB. The
FIB maintains next-hop address information based on the information in the IP routing table. Because there is a one-to-one correlation between FIB entries and routing table entries, the FIB contains all known routes and eliminates the need for route cache maintenance that is associated with earlier switching paths such as fast switching and optimum switching.
Note: In order to view the Routing information base (RIB) table, use the "show ip route" command.
To view the Forwarding Information Base (FIB), use the "show ip cef" command. RIB is in Control plane while FIB is in Data plane.
QUESTION NO: 4
Refer to the exhibit. A port channel is configured between SW2 and SW3. SW2 is not running a
Cisco operating system. When all physical connections are mode, the port channel does not establish.
Based on the configuration excerpt of SW3, what is the cause of the problem?
A. The port-channel interface lead balance should be set to src-mac
B. The port-channel trunk is not allowing the native VLAN.
C. The port-channel should be set to auto.
D. The port channel on SW2 is using an incompatible protocol.
Answer: D
Explanation:
The Cisco switch was configured with PAgP, which is a Cisco proprietary protocol so non-Cisco switch could not communicate.
QUESTION NO: 5
Which statement about multicast RPs is true?
A. RPs are required for protocol independent multicast sparse mode and dense mode.
B. By default, the RP is needed only to start new sessions with sources and receivers.
C. By default, the RP is needed periodically to maintain sessions with sources and receivers
D. RPs are required only when using protocol independent multicast dense mode.
Answer: B
Explanation:
A rendezvous point (RP) is required only in networks running Protocol Independent Multicast sparse mode (PIM-SM).
By default, the RP is needed only to start new sessions with sources and receivers.
Reference:
https://www.cisco.com/c/en/us/td/docs/ios/solutions_docs/ip_multicast/White_papers/rps.html
For your information, in PIM-SM, only network segments with active receivers that have explicitly requested multicast data will be forwarded the traffic. This method of delivering multicast data is in contrast to the PIM dense mode (PIM-DM) model. In PIM-DM, multicast traffic is initially flooded to all segments of the network. Routers that have no downstream neighbors or directly connected receivers prune back the unwanted traffic.
With years of experience dealing with VMware 3V0-42.23 learning engine, we have thorough grasp of knowledge which appears clearly in our VMware 3V0-42.23 study quiz with all the keypoints and the latest questions and answers. GAQM CSCM-001 - Now IT industry is more and more competitive. Just come to buy our PECB ISO-IEC-27001-Lead-Auditor-KR learning guide and you will love it. If you are still struggling to prepare for passing VMware 5V0-92.22 certification exam, at this moment Omgzlook can help you solve problem. Free demos are understandable and part of the Autodesk ACP-01101 exam materials as well as the newest information for your practice.
Updated: May 28, 2022