You can totally trust us. We are trying our best to meet your demands. Why not give our Cisco study materials a chance? Our products will live up to your expectations. Our service staff will help you solve the problem about the 350-401 Test Cram Sheet training materials with the most professional knowledge and enthusiasm. We believe that can completely dispel your worries on 350-401 Test Cram Sheet exam braindumps. The immediate downloading feature of our 350-401 Test Cram Sheet study materials is an eminent advantage of our products.
CCNP Enterprise 350-401 They compile each answer and question carefully.
Our Cisco certification 350-401 - Implementing Cisco Enterprise Network Core Technologies (350-401 ENCOR) Test Cram Sheet exam question bank is produced by Omgzlook's experts's continuously research of outline and previous exam. We sincerely hope that you can achieve your dream in the near future by the Latest 350-401 Practice Questions Ppt latest questions of our company. There are a lot of experts and professors in or company in the field.
We can let you spend a small amount of time and money and pass the IT certification exam at the same time. Selecting the products of Omgzlook to help you pass your first time Cisco certification 350-401 Test Cram Sheet exam is very cost-effective. Omgzlook provide a good after-sales service for all customers.
Cisco 350-401 Test Cram Sheet - It can help you pass the exam successfully.
The moment you choose to go with our 350-401 Test Cram Sheet study materials, your dream will be more clearly presented to you. Next, through my introduction, I hope you can have a deeper understanding of our 350-401 Test Cram Sheet learning quiz. We really hope that our 350-401 Test Cram Sheet practice engine will give you some help. In fact, our 350-401 Test Cram Sheet exam questions have helped tens of thousands of our customers successfully achieve their certification.
So you have to seize this opportunity of Omgzlook. Only with it can you show your skills.
350-401 PDF DEMO:
QUESTION NO: 1
Refer to the exhibit. A port channel is configured between SW2 and SW3. SW2 is not running a
Cisco operating system. When all physical connections are mode, the port channel does not establish.
Based on the configuration excerpt of SW3, what is the cause of the problem?
A. The port-channel interface lead balance should be set to src-mac
B. The port-channel trunk is not allowing the native VLAN.
C. The port-channel should be set to auto.
D. The port channel on SW2 is using an incompatible protocol.
Answer: D
Explanation:
The Cisco switch was configured with PAgP, which is a Cisco proprietary protocol so non-Cisco switch could not communicate.
QUESTION NO: 2
Which statement about multicast RPs is true?
A. RPs are required for protocol independent multicast sparse mode and dense mode.
B. By default, the RP is needed only to start new sessions with sources and receivers.
C. By default, the RP is needed periodically to maintain sessions with sources and receivers
D. RPs are required only when using protocol independent multicast dense mode.
Answer: B
Explanation:
A rendezvous point (RP) is required only in networks running Protocol Independent Multicast sparse mode (PIM-SM).
By default, the RP is needed only to start new sessions with sources and receivers.
Reference:
https://www.cisco.com/c/en/us/td/docs/ios/solutions_docs/ip_multicast/White_papers/rps.html
For your information, in PIM-SM, only network segments with active receivers that have explicitly requested multicast data will be forwarded the traffic. This method of delivering multicast data is in contrast to the PIM dense mode (PIM-DM) model. In PIM-DM, multicast traffic is initially flooded to all segments of the network. Routers that have no downstream neighbors or directly connected receivers prune back the unwanted traffic.
QUESTION NO: 3
Which technology provides a secure communication channel for all traffic at Layer 2 of the OSI model?
A. IPsec
B. Cisco Trustsec
C. MACsec
D. SSL
Answer: C
Explanation:
MACsec, defined in 802.1AE, provides MAC-layer encryption over wired networks by using out- of
-band methods for encryption keying. The MACsec Key Agreement (MKA) Protocol provides the required session keys and manages the required encryption keys. MKA and MACsec are implemented after successful authentication using the 802.1x Extensible Authentication Protocol (EAP-TLS) or Pre
Shared Key (PSK) framework.
A switch using MACsec accepts either MACsec or non-MACsec frames, depending on the policy associated with the MKA peer. MACsec frames are encrypted and protected with an integrity check value (ICV). When the switch receives frames from the MKA peer, it decrypts them and calculates the correct ICV by using session keys provided by MKA. The switch compares that ICV to the ICV within the frame. If they are not identical, the frame is dropped. The switch also encrypts and adds an ICV to any frames sent over the secured port (the access point used to provide the secure MAC service to a
MKA peer) using the current session key.
Reference: https://www.cisco.com/c/en/us/td/docs/switches/lan/catalyst9300/software/release/16-
9/configuration_guide/sec/b_169_sec_9300_cg/macsec_encryption.html
Note: Cisco Trustsec is the solution which includes MACsec.
QUESTION NO: 4
To increase total throughput and redundancy on the links between the wireless controller and switch, the customer enabled LAG on the wireless controller.
Which EtherChannel mode must be configured on the switch to allow the WLC to connect?
A. Active
B. On
C. Auto
D. Passive
Answer: B
Explanation:
Restrictions for Link Aggregation:
You can bundle all eight ports on a Cisco 5508 Controller into a single link.
Terminating on two different modules within a single Catalyst 6500 series switch provides redundancy and ensures that connectivity between the switch and the controller is maintained when one module fails. The controller's port 1 is connected to Gigabit interface 3/1, and the controller's port 2 is connected to Gigabit interface 2/1 on the Catalyst 6500 series switch. Both switch ports are assigned to the same channel group.
LAG requires the EtherChannel to be configured for 'mode on' on both the controller and the Catalyst switch.
Once the EtherChannel is configured as on at both ends of the link, the Catalyst switch should not be configured for either Link Aggregation Control Protocol (LACP) or Cisco proprietary Port Aggregation
Protocol (PAgP) but be set unconditionally to LAG. Because no channel negotiation is done between the controller and the switch, the controller does not answer to negotiation frames and the LAG is not formed if a dynamic form of LAG is set on the switch. Additionally, LACP and PAgP are not supported on the controller.
If the recommended load-balancing method cannot be configured on the Catalyst switch, then configure the LAG connection as a single member link or disable LAG on the controller.
https://www.cisco.com/c/en/us/td/docs/wireless/controller/7-5/configuration- guide/b_cg75/b_cg75_chapter_0100010.html
QUESTION NO: 5
Which access controls list allows only TCP traffic with a destination port range of 22-433, excluding port 80?
A. Deny tcp any any ne 80
Permit tcp any any range 22 443
B. Permit tcp any any ne 80
C. Permit tco any any range 22 443
Deny tcp any any eq 80
D. Deny tcp any any eq 80
Permit tco any any gt 21 it 444
Answer: D
Now that more people are using mobile phones to learn our Huawei H23-221_V1.0 study guide, you can also choose the one you like. APM APM-PFQ - The high quality exam dumps can produce a wonderful effect. Once you have submitted your practice time, Juniper JN0-649 study tool system will automatically complete your operation. Would you like to register Cisco Amazon DOP-C02-KR certification test? Would you like to obtain Amazon DOP-C02-KR certificate? Without having enough time to prepare for the exam, what should you do to pass your exam? In fact, there are techniques that can help. In such a tough situation, how can we highlight our advantages? It may be a good way to get the test Oracle 1z1-808-KR certification.
Updated: May 28, 2022