And then, to take Cisco 350-401 Training Tools exam can help you to express your desire. Don't worry. Omgzlook will help you to find what you need in the exam and our dumps must help you to obtain 350-401 Training Tools certificate. Our 350-401 Training Tools study materials are famous for its high-efficiency and high-quality. If you buy our 350-401 Training Tools learning guide, you will find that the exam is just a piece of cake in front of you. If you successfully get Cisco 350-401 Training Tools certificate, you can finish your work better.
CCNP Enterprise 350-401 Our products are just suitable for you.
CCNP Enterprise 350-401 Training Tools - Implementing Cisco Enterprise Network Core Technologies (350-401 ENCOR) The training materials of Omgzlook are developed by many IT experts' continuously using their experience and knowledge to study, and the quality is very good and have very high accuracy. You will get your 350-401 Vce Test Simulator certification with little time and energy by the help of out dumps. Omgzlook is constantly updated in accordance with the changing requirements of the Cisco certification.
If you buy the Omgzlook's products, we will not only spare no effort to help you pass the certification exam, but also provide a free update and upgrade service. If the official change the outline of the certification exam, we will notify customers immediately. If we have any updated version of test software, it will be immediately pushed to customers.
Cisco 350-401 Training Tools - 100% guarantee to pass IT certification test.
The disparity between our 350-401 Training Tools practice materials and others are distinct. We strive for perfection all these years and get satisfactory results with concerted cooperation between experts, and all questions points in our 350-401 Training Tools real exam are devised and written base on the real exam. Do not let other 350-401 Training Tools study dumps mess up your performance or aggravate learning difficulties. The efficiency and accuracy of our 350-401 Training Tools learning guide will not let you down.
If you don't want to waste a lot of time and efforts on the exam, you had better select Omgzlook Cisco 350-401 Training Tools dumps. Using this certification training dumps can let you improve the efficiency of your studying so that it can help you save much more time.
350-401 PDF DEMO:
QUESTION NO: 1
To increase total throughput and redundancy on the links between the wireless controller and switch, the customer enabled LAG on the wireless controller.
Which EtherChannel mode must be configured on the switch to allow the WLC to connect?
A. Active
B. On
C. Auto
D. Passive
Answer: B
Explanation:
Restrictions for Link Aggregation:
You can bundle all eight ports on a Cisco 5508 Controller into a single link.
Terminating on two different modules within a single Catalyst 6500 series switch provides redundancy and ensures that connectivity between the switch and the controller is maintained when one module fails. The controller's port 1 is connected to Gigabit interface 3/1, and the controller's port 2 is connected to Gigabit interface 2/1 on the Catalyst 6500 series switch. Both switch ports are assigned to the same channel group.
LAG requires the EtherChannel to be configured for 'mode on' on both the controller and the Catalyst switch.
Once the EtherChannel is configured as on at both ends of the link, the Catalyst switch should not be configured for either Link Aggregation Control Protocol (LACP) or Cisco proprietary Port Aggregation
Protocol (PAgP) but be set unconditionally to LAG. Because no channel negotiation is done between the controller and the switch, the controller does not answer to negotiation frames and the LAG is not formed if a dynamic form of LAG is set on the switch. Additionally, LACP and PAgP are not supported on the controller.
If the recommended load-balancing method cannot be configured on the Catalyst switch, then configure the LAG connection as a single member link or disable LAG on the controller.
https://www.cisco.com/c/en/us/td/docs/wireless/controller/7-5/configuration- guide/b_cg75/b_cg75_chapter_0100010.html
QUESTION NO: 2
Which technology provides a secure communication channel for all traffic at Layer 2 of the OSI model?
A. IPsec
B. Cisco Trustsec
C. MACsec
D. SSL
Answer: C
Explanation:
MACsec, defined in 802.1AE, provides MAC-layer encryption over wired networks by using out- of
-band methods for encryption keying. The MACsec Key Agreement (MKA) Protocol provides the required session keys and manages the required encryption keys. MKA and MACsec are implemented after successful authentication using the 802.1x Extensible Authentication Protocol (EAP-TLS) or Pre
Shared Key (PSK) framework.
A switch using MACsec accepts either MACsec or non-MACsec frames, depending on the policy associated with the MKA peer. MACsec frames are encrypted and protected with an integrity check value (ICV). When the switch receives frames from the MKA peer, it decrypts them and calculates the correct ICV by using session keys provided by MKA. The switch compares that ICV to the ICV within the frame. If they are not identical, the frame is dropped. The switch also encrypts and adds an ICV to any frames sent over the secured port (the access point used to provide the secure MAC service to a
MKA peer) using the current session key.
Reference: https://www.cisco.com/c/en/us/td/docs/switches/lan/catalyst9300/software/release/16-
9/configuration_guide/sec/b_169_sec_9300_cg/macsec_encryption.html
Note: Cisco Trustsec is the solution which includes MACsec.
QUESTION NO: 3
Refer to the exhibit. A port channel is configured between SW2 and SW3. SW2 is not running a
Cisco operating system. When all physical connections are mode, the port channel does not establish.
Based on the configuration excerpt of SW3, what is the cause of the problem?
A. The port-channel interface lead balance should be set to src-mac
B. The port-channel trunk is not allowing the native VLAN.
C. The port-channel should be set to auto.
D. The port channel on SW2 is using an incompatible protocol.
Answer: D
Explanation:
The Cisco switch was configured with PAgP, which is a Cisco proprietary protocol so non-Cisco switch could not communicate.
QUESTION NO: 4
What is the difference between a RIB and a FIB?
A. The FIB is populated based on RIB content
B. The RIB is used to make IP source prefix-based switching decisions
C. The RIB maintains a mirror image of the FIB
D. The FIB is where all IP routing information is stored
Answer: A
Explanation:
CEF uses a Forwarding Information Base (FIB) to make IP destination prefix-based switching decisions.
The FIB is conceptually similar to a routing table or information base. It maintains a mirror image of the forwarding information contained in the IP routing table. When routing or topology changes occur in the network, the IP routing table is updated, and those changes are reflected in the FIB. The
FIB maintains next-hop address information based on the information in the IP routing table. Because there is a one-to-one correlation between FIB entries and routing table entries, the FIB contains all known routes and eliminates the need for route cache maintenance that is associated with earlier switching paths such as fast switching and optimum switching.
Note: In order to view the Routing information base (RIB) table, use the "show ip route" command.
To view the Forwarding Information Base (FIB), use the "show ip cef" command. RIB is in Control plane while FIB is in Data plane.
QUESTION NO: 5
Which statement about multicast RPs is true?
A. RPs are required for protocol independent multicast sparse mode and dense mode.
B. By default, the RP is needed only to start new sessions with sources and receivers.
C. By default, the RP is needed periodically to maintain sessions with sources and receivers
D. RPs are required only when using protocol independent multicast dense mode.
Answer: B
Explanation:
A rendezvous point (RP) is required only in networks running Protocol Independent Multicast sparse mode (PIM-SM).
By default, the RP is needed only to start new sessions with sources and receivers.
Reference:
https://www.cisco.com/c/en/us/td/docs/ios/solutions_docs/ip_multicast/White_papers/rps.html
For your information, in PIM-SM, only network segments with active receivers that have explicitly requested multicast data will be forwarded the traffic. This method of delivering multicast data is in contrast to the PIM dense mode (PIM-DM) model. In PIM-DM, multicast traffic is initially flooded to all segments of the network. Routers that have no downstream neighbors or directly connected receivers prune back the unwanted traffic.
Remember that each EMC D-SNC-DY-00 exam preparation is built from a common certification foundation.EMC D-SNC-DY-00 prepareation will provide the most excellent and simple method to pass your EMC D-SNC-DY-00 Certification Exams on the first attempt. Omgzlook won a good reputation by these candidates that have passed Cisco Netskope NSK300 certification exam. The Google Professional-Cloud-Architect preparation products available here are provided in line with latest changes and updates in Google Professional-Cloud-Architect syllabus. Our IT elite finally designs the best Splunk SPLK-5002 exam study materials by collecting the complex questions and analyzing the focal points of the exam over years. After our unremitting efforts, Microsoft AI-102 learning guide comes in everybody's expectation.
Updated: May 28, 2022