Trust us and you will get success for sure! With 350-401 Real Exam certificate, you will harvest many points of theories that others ignore and can offer strong prove for managers. So the 350-401 Real Exam exam is a great beginning. As long as you follow with our 350-401 Real Exam study guide, you are doomed to achieve your success. We have applied the latest technologies to the design of our 350-401 Real Exam exam prep not only on the content but also on the displays. Besides, we guarantee that the 350-401 Real Exam exam questions of all our users can be answered by professional personal in the shortest time with our 350-401 Real Exam study dumps.
CCNP Enterprise 350-401 It is your right time to make your mark.
Secondly, since our 350-401 - Implementing Cisco Enterprise Network Core Technologies (350-401 ENCOR) Real Exam training quiz appeared on the market, seldom do we have the cases of customer information disclosure. During the prolonged review, many exam candidates feel wondering attention is hard to focus. But our Study 350-401 Notes real exam is high efficient which can pass the Study 350-401 Notes exam during a week.
The questions of our 350-401 Real Exam guide questions are related to the latest and basic knowledge. What’s more, our 350-401 Real Exam learning materials are committed to grasp the most knowledgeable points with the fewest problems. So 20-30 hours of study is enough for you to deal with the exam.
Cisco 350-401 Real Exam - They will mitigate your chance of losing.
Dear customers, you may think it is out of your league before such as winning the 350-401 Real Exam exam practice is possible within a week or a 350-401 Real Exam practice material could have passing rate over 98 percent. This time it will not be illusions for you anymore. You can learn some authentic knowledge with our high accuracy and efficiency 350-401 Real Exam simulating questions and help you get authentic knowledge of the exam.
You can send us an email to ask questions at anytime, anywhere. For any questions you may have during the use of 350-401 Real Exam exam questions, our customer service staff will be patient to help you to solve them.
350-401 PDF DEMO:
QUESTION NO: 1
What is the difference between a RIB and a FIB?
A. The FIB is populated based on RIB content
B. The RIB is used to make IP source prefix-based switching decisions
C. The RIB maintains a mirror image of the FIB
D. The FIB is where all IP routing information is stored
Answer: A
Explanation:
CEF uses a Forwarding Information Base (FIB) to make IP destination prefix-based switching decisions.
The FIB is conceptually similar to a routing table or information base. It maintains a mirror image of the forwarding information contained in the IP routing table. When routing or topology changes occur in the network, the IP routing table is updated, and those changes are reflected in the FIB. The
FIB maintains next-hop address information based on the information in the IP routing table. Because there is a one-to-one correlation between FIB entries and routing table entries, the FIB contains all known routes and eliminates the need for route cache maintenance that is associated with earlier switching paths such as fast switching and optimum switching.
Note: In order to view the Routing information base (RIB) table, use the "show ip route" command.
To view the Forwarding Information Base (FIB), use the "show ip cef" command. RIB is in Control plane while FIB is in Data plane.
QUESTION NO: 2
Which feature does Cisco TrustSec use to provide scalable, secure communication throughout a network?
A. security group tag number assigned to each user on a switch
B. security group tag ACL assigned to each router on a network
C. security group tag ACL assigned to each port on a switch
D. security group tag number assigned to each port on a network
Answer: D
Explanation:
Cisco TrustSec uses tags to represent logical group privilege. This tag, called a Security Group Tag
(SGT), is used in access policies. The SGT is understood and is used to enforce traffic by Cisco switches, routers and firewalls . Cisco TrustSec is defined in three phases: classification, propagation and enforcement.
When users and devices connect to a network, the network assigns a specific security group.
This process is called classification. Classification can be based on the results of the authentication or by associating the SGT with an IP, VLAN, or port-profile (-> Answer A and answer C are not correct as they say "assigned ... on a switch" only. Answer D is not correct either as it says "assigned to each router").
QUESTION NO: 3
To increase total throughput and redundancy on the links between the wireless controller and switch, the customer enabled LAG on the wireless controller.
Which EtherChannel mode must be configured on the switch to allow the WLC to connect?
A. Active
B. On
C. Auto
D. Passive
Answer: B
Explanation:
Restrictions for Link Aggregation:
You can bundle all eight ports on a Cisco 5508 Controller into a single link.
Terminating on two different modules within a single Catalyst 6500 series switch provides redundancy and ensures that connectivity between the switch and the controller is maintained when one module fails. The controller's port 1 is connected to Gigabit interface 3/1, and the controller's port 2 is connected to Gigabit interface 2/1 on the Catalyst 6500 series switch. Both switch ports are assigned to the same channel group.
LAG requires the EtherChannel to be configured for 'mode on' on both the controller and the Catalyst switch.
Once the EtherChannel is configured as on at both ends of the link, the Catalyst switch should not be configured for either Link Aggregation Control Protocol (LACP) or Cisco proprietary Port Aggregation
Protocol (PAgP) but be set unconditionally to LAG. Because no channel negotiation is done between the controller and the switch, the controller does not answer to negotiation frames and the LAG is not formed if a dynamic form of LAG is set on the switch. Additionally, LACP and PAgP are not supported on the controller.
If the recommended load-balancing method cannot be configured on the Catalyst switch, then configure the LAG connection as a single member link or disable LAG on the controller.
https://www.cisco.com/c/en/us/td/docs/wireless/controller/7-5/configuration- guide/b_cg75/b_cg75_chapter_0100010.html
QUESTION NO: 4
Which technology provides a secure communication channel for all traffic at Layer 2 of the OSI model?
A. IPsec
B. Cisco Trustsec
C. MACsec
D. SSL
Answer: C
Explanation:
MACsec, defined in 802.1AE, provides MAC-layer encryption over wired networks by using out- of
-band methods for encryption keying. The MACsec Key Agreement (MKA) Protocol provides the required session keys and manages the required encryption keys. MKA and MACsec are implemented after successful authentication using the 802.1x Extensible Authentication Protocol (EAP-TLS) or Pre
Shared Key (PSK) framework.
A switch using MACsec accepts either MACsec or non-MACsec frames, depending on the policy associated with the MKA peer. MACsec frames are encrypted and protected with an integrity check value (ICV). When the switch receives frames from the MKA peer, it decrypts them and calculates the correct ICV by using session keys provided by MKA. The switch compares that ICV to the ICV within the frame. If they are not identical, the frame is dropped. The switch also encrypts and adds an ICV to any frames sent over the secured port (the access point used to provide the secure MAC service to a
MKA peer) using the current session key.
Reference: https://www.cisco.com/c/en/us/td/docs/switches/lan/catalyst9300/software/release/16-
9/configuration_guide/sec/b_169_sec_9300_cg/macsec_encryption.html
Note: Cisco Trustsec is the solution which includes MACsec.
QUESTION NO: 5
Refer to the exhibit. A port channel is configured between SW2 and SW3. SW2 is not running a
Cisco operating system. When all physical connections are mode, the port channel does not establish.
Based on the configuration excerpt of SW3, what is the cause of the problem?
A. The port-channel interface lead balance should be set to src-mac
B. The port-channel trunk is not allowing the native VLAN.
C. The port-channel should be set to auto.
D. The port channel on SW2 is using an incompatible protocol.
Answer: D
Explanation:
The Cisco switch was configured with PAgP, which is a Cisco proprietary protocol so non-Cisco switch could not communicate.
With our Lpi 050-100 study materials, all your agreeable outcomes are no longer dreams for you. Only 20-30 hours on our OMSB OMSB_OEN learning guide are needed for the client to prepare for the test and it saves our client’s time and energy. Our AACN CCRN-Adult learning material was compiled from the wisdom and sweat of many industry experts. We can make sure that our WGU Cybersecurity-Architecture-and-Engineering study materials have the ability to help you solve your problem, and you will not be troubled by these questions above. The exercises and answers of our SAP C-S4FCF-2023 exam questions are designed by our experts to perfectly answer the puzzles you may encounter in preparing for the exam and save you valuable time.
Updated: May 28, 2022