Through so many feedbacks of these products, our Omgzlook products prove to be trusted. Omgzlook have the latest Cisco certification 350-401 Lab Simulation exam training materials. The industrious Omgzlook's IT experts through their own expertise and experience continuously produce the latest Cisco 350-401 Lab Simulation training materials to facilitate IT professionals to pass the Cisco certification 350-401 Lab Simulation exam. Since we have the same ultimate goals, which is successfully pass the 350-401 Lab Simulation exam. So during your formative process of preparation, we are willing be your side all the time. If you fail to pass the exam, Omgzlook will full refund to you.
CCNP Enterprise 350-401 A bad situation can show special integrity.
And we believe you will pass the 350-401 - Implementing Cisco Enterprise Network Core Technologies (350-401 ENCOR) Lab Simulation exam just like the other people! Since to choose to participate in the Cisco 350-401 Reliable Exam Camp File certification exam, of course, it is necessary to have to go through. This is also the performance that you are strong-willed.
We are confident that your future goals will begin with this successful exam. So choosing our 350-401 Lab Simulation training materials is a wise choice. Our 350-401 Lab Simulationpractice materials will provide you with a platform of knowledge to help you achieve your dream.
Cisco 350-401 Lab Simulation - Our key advantages are that 1.
Perhaps you have wasted a lot of time to playing computer games. It doesn’t matter. It is never too late to change. There is no point in regretting for the past. Our 350-401 Lab Simulation exam questions can help you compensate for the mistakes you have made in the past. You will change a lot after learning our 350-401 Lab Simulation study materials. And most of all, you will get reward by our 350-401 Lab Simulation training engine in the least time with little effort.
If you are urgent to pass exam our exam materials will be suitable for you. Mostly you just need to remember the questions and answers of our Cisco 350-401 Lab Simulation exam review questions and you will clear exams.
350-401 PDF DEMO:
QUESTION NO: 1
To increase total throughput and redundancy on the links between the wireless controller and switch, the customer enabled LAG on the wireless controller.
Which EtherChannel mode must be configured on the switch to allow the WLC to connect?
A. Active
B. On
C. Auto
D. Passive
Answer: B
Explanation:
Restrictions for Link Aggregation:
You can bundle all eight ports on a Cisco 5508 Controller into a single link.
Terminating on two different modules within a single Catalyst 6500 series switch provides redundancy and ensures that connectivity between the switch and the controller is maintained when one module fails. The controller's port 1 is connected to Gigabit interface 3/1, and the controller's port 2 is connected to Gigabit interface 2/1 on the Catalyst 6500 series switch. Both switch ports are assigned to the same channel group.
LAG requires the EtherChannel to be configured for 'mode on' on both the controller and the Catalyst switch.
Once the EtherChannel is configured as on at both ends of the link, the Catalyst switch should not be configured for either Link Aggregation Control Protocol (LACP) or Cisco proprietary Port Aggregation
Protocol (PAgP) but be set unconditionally to LAG. Because no channel negotiation is done between the controller and the switch, the controller does not answer to negotiation frames and the LAG is not formed if a dynamic form of LAG is set on the switch. Additionally, LACP and PAgP are not supported on the controller.
If the recommended load-balancing method cannot be configured on the Catalyst switch, then configure the LAG connection as a single member link or disable LAG on the controller.
https://www.cisco.com/c/en/us/td/docs/wireless/controller/7-5/configuration- guide/b_cg75/b_cg75_chapter_0100010.html
QUESTION NO: 2
What is the difference between a RIB and a FIB?
A. The FIB is populated based on RIB content
B. The RIB is used to make IP source prefix-based switching decisions
C. The RIB maintains a mirror image of the FIB
D. The FIB is where all IP routing information is stored
Answer: A
Explanation:
CEF uses a Forwarding Information Base (FIB) to make IP destination prefix-based switching decisions.
The FIB is conceptually similar to a routing table or information base. It maintains a mirror image of the forwarding information contained in the IP routing table. When routing or topology changes occur in the network, the IP routing table is updated, and those changes are reflected in the FIB. The
FIB maintains next-hop address information based on the information in the IP routing table. Because there is a one-to-one correlation between FIB entries and routing table entries, the FIB contains all known routes and eliminates the need for route cache maintenance that is associated with earlier switching paths such as fast switching and optimum switching.
Note: In order to view the Routing information base (RIB) table, use the "show ip route" command.
To view the Forwarding Information Base (FIB), use the "show ip cef" command. RIB is in Control plane while FIB is in Data plane.
QUESTION NO: 3
Which technology provides a secure communication channel for all traffic at Layer 2 of the OSI model?
A. IPsec
B. Cisco Trustsec
C. MACsec
D. SSL
Answer: C
Explanation:
MACsec, defined in 802.1AE, provides MAC-layer encryption over wired networks by using out- of
-band methods for encryption keying. The MACsec Key Agreement (MKA) Protocol provides the required session keys and manages the required encryption keys. MKA and MACsec are implemented after successful authentication using the 802.1x Extensible Authentication Protocol (EAP-TLS) or Pre
Shared Key (PSK) framework.
A switch using MACsec accepts either MACsec or non-MACsec frames, depending on the policy associated with the MKA peer. MACsec frames are encrypted and protected with an integrity check value (ICV). When the switch receives frames from the MKA peer, it decrypts them and calculates the correct ICV by using session keys provided by MKA. The switch compares that ICV to the ICV within the frame. If they are not identical, the frame is dropped. The switch also encrypts and adds an ICV to any frames sent over the secured port (the access point used to provide the secure MAC service to a
MKA peer) using the current session key.
Reference: https://www.cisco.com/c/en/us/td/docs/switches/lan/catalyst9300/software/release/16-
9/configuration_guide/sec/b_169_sec_9300_cg/macsec_encryption.html
Note: Cisco Trustsec is the solution which includes MACsec.
QUESTION NO: 4
Refer to the exhibit. A port channel is configured between SW2 and SW3. SW2 is not running a
Cisco operating system. When all physical connections are mode, the port channel does not establish.
Based on the configuration excerpt of SW3, what is the cause of the problem?
A. The port-channel interface lead balance should be set to src-mac
B. The port-channel trunk is not allowing the native VLAN.
C. The port-channel should be set to auto.
D. The port channel on SW2 is using an incompatible protocol.
Answer: D
Explanation:
The Cisco switch was configured with PAgP, which is a Cisco proprietary protocol so non-Cisco switch could not communicate.
QUESTION NO: 5
Which feature does Cisco TrustSec use to provide scalable, secure communication throughout a network?
A. security group tag number assigned to each user on a switch
B. security group tag ACL assigned to each router on a network
C. security group tag ACL assigned to each port on a switch
D. security group tag number assigned to each port on a network
Answer: D
Explanation:
Cisco TrustSec uses tags to represent logical group privilege. This tag, called a Security Group Tag
(SGT), is used in access policies. The SGT is understood and is used to enforce traffic by Cisco switches, routers and firewalls . Cisco TrustSec is defined in three phases: classification, propagation and enforcement.
When users and devices connect to a network, the network assigns a specific security group.
This process is called classification. Classification can be based on the results of the authentication or by associating the SGT with an IP, VLAN, or port-profile (-> Answer A and answer C are not correct as they say "assigned ... on a switch" only. Answer D is not correct either as it says "assigned to each router").
Databricks Databricks-Machine-Learning-Associate - There is no doubt that the certification has become more and more important for a lot of people, especial these people who are looking for a good job, and it has been a general trend. Microsoft MB-800 - Please totally trust the accuracy of questions and answers. After a long period of research and development, our Salesforce Customer-Data-Platform test questions have been the leader study materials in the field. The HP HPE0-V28 test answers are tested and approved by our certified experts and you can check the accuracy of our questions from our free demo. And you can free download the demos of the Google ChromeOS-Administrator learning quiz.
Updated: May 28, 2022