It doesn’t matter if it's your first time to attend 350-401 Guide Materials practice test or if you are freshman in the IT certification test, our latest 350-401 Guide Materials dumps guide will boost you confidence to face the challenge. Our dumps collection will save you much time and ensure you get high mark in 350-401 Guide Materials actual test with less effort. Come and check the free demo in our website you won’t regret it. About Cisco 350-401 Guide Materials exam, you can find these questions from different web sites or books, but the key is logical and connected. Our questions and answers will not only allow you effortlessly through the exam first time, but also can save your valuable time. We guarantee full refund for any reason in case of your failure of 350-401 Guide Materials test.
CCNP Enterprise 350-401 100% guarantee to pass IT certification test.
We strive for perfection all these years and get satisfactory results with concerted cooperation between experts, and all questions points in our 350-401 - Implementing Cisco Enterprise Network Core Technologies (350-401 ENCOR) Guide Materials real exam are devised and written base on the real exam. This is a special IT exam dumps for all candidates. Omgzlook pdf real questions and answers will help you prepare well enough for Cisco Training 350-401 Kit test in the short period of time and pass your exam successfully.
Omgzlook 350-401 Guide Materials exam preparation begins and ends with your accomplishing this credential goal. Although you will take each 350-401 Guide Materials online test one at a time - each one builds upon the previous. Remember that each 350-401 Guide Materials exam preparation is built from a common certification foundation.350-401 Guide Materials prepareation will provide the most excellent and simple method to pass your 350-401 Guide Materials Certification Exams on the first attempt.
Cisco 350-401 Guide Materials - You can study any time anywhere you want.
We guarantee that after purchasing our 350-401 Guide Materials exam torrent, we will deliver the product to you as soon as possible within ten minutes. So you don’t need to wait for a long time and worry about the delivery time or any delay. We will transfer our Implementing Cisco Enterprise Network Core Technologies (350-401 ENCOR) prep torrent to you online immediately, and this service is also the reason why our 350-401 Guide Materials test braindumps can win people’s heart and mind. Therefore, you are able to get hang of the essential points in a shorter time compared to those who are not willing to use our 350-401 Guide Materials exam torrent.
Our IT professionals have made their best efforts to offer you the latest 350-401 Guide Materials study guide in a smart way for the certification exam preparation. With the help of our 350-401 Guide Materials dumps collection, all level of candidates can grasp the key content of the real exam and solve the difficulty of 350-401 Guide Materials real questions easily.
350-401 PDF DEMO:
QUESTION NO: 1
Which technology provides a secure communication channel for all traffic at Layer 2 of the OSI model?
A. IPsec
B. Cisco Trustsec
C. MACsec
D. SSL
Answer: C
Explanation:
MACsec, defined in 802.1AE, provides MAC-layer encryption over wired networks by using out- of
-band methods for encryption keying. The MACsec Key Agreement (MKA) Protocol provides the required session keys and manages the required encryption keys. MKA and MACsec are implemented after successful authentication using the 802.1x Extensible Authentication Protocol (EAP-TLS) or Pre
Shared Key (PSK) framework.
A switch using MACsec accepts either MACsec or non-MACsec frames, depending on the policy associated with the MKA peer. MACsec frames are encrypted and protected with an integrity check value (ICV). When the switch receives frames from the MKA peer, it decrypts them and calculates the correct ICV by using session keys provided by MKA. The switch compares that ICV to the ICV within the frame. If they are not identical, the frame is dropped. The switch also encrypts and adds an ICV to any frames sent over the secured port (the access point used to provide the secure MAC service to a
MKA peer) using the current session key.
Reference: https://www.cisco.com/c/en/us/td/docs/switches/lan/catalyst9300/software/release/16-
9/configuration_guide/sec/b_169_sec_9300_cg/macsec_encryption.html
Note: Cisco Trustsec is the solution which includes MACsec.
QUESTION NO: 2
To increase total throughput and redundancy on the links between the wireless controller and switch, the customer enabled LAG on the wireless controller.
Which EtherChannel mode must be configured on the switch to allow the WLC to connect?
A. Active
B. On
C. Auto
D. Passive
Answer: B
Explanation:
Restrictions for Link Aggregation:
You can bundle all eight ports on a Cisco 5508 Controller into a single link.
Terminating on two different modules within a single Catalyst 6500 series switch provides redundancy and ensures that connectivity between the switch and the controller is maintained when one module fails. The controller's port 1 is connected to Gigabit interface 3/1, and the controller's port 2 is connected to Gigabit interface 2/1 on the Catalyst 6500 series switch. Both switch ports are assigned to the same channel group.
LAG requires the EtherChannel to be configured for 'mode on' on both the controller and the Catalyst switch.
Once the EtherChannel is configured as on at both ends of the link, the Catalyst switch should not be configured for either Link Aggregation Control Protocol (LACP) or Cisco proprietary Port Aggregation
Protocol (PAgP) but be set unconditionally to LAG. Because no channel negotiation is done between the controller and the switch, the controller does not answer to negotiation frames and the LAG is not formed if a dynamic form of LAG is set on the switch. Additionally, LACP and PAgP are not supported on the controller.
If the recommended load-balancing method cannot be configured on the Catalyst switch, then configure the LAG connection as a single member link or disable LAG on the controller.
https://www.cisco.com/c/en/us/td/docs/wireless/controller/7-5/configuration- guide/b_cg75/b_cg75_chapter_0100010.html
QUESTION NO: 3
Refer to the exhibit. A port channel is configured between SW2 and SW3. SW2 is not running a
Cisco operating system. When all physical connections are mode, the port channel does not establish.
Based on the configuration excerpt of SW3, what is the cause of the problem?
A. The port-channel interface lead balance should be set to src-mac
B. The port-channel trunk is not allowing the native VLAN.
C. The port-channel should be set to auto.
D. The port channel on SW2 is using an incompatible protocol.
Answer: D
Explanation:
The Cisco switch was configured with PAgP, which is a Cisco proprietary protocol so non-Cisco switch could not communicate.
QUESTION NO: 4
What is the difference between a RIB and a FIB?
A. The FIB is populated based on RIB content
B. The RIB is used to make IP source prefix-based switching decisions
C. The RIB maintains a mirror image of the FIB
D. The FIB is where all IP routing information is stored
Answer: A
Explanation:
CEF uses a Forwarding Information Base (FIB) to make IP destination prefix-based switching decisions.
The FIB is conceptually similar to a routing table or information base. It maintains a mirror image of the forwarding information contained in the IP routing table. When routing or topology changes occur in the network, the IP routing table is updated, and those changes are reflected in the FIB. The
FIB maintains next-hop address information based on the information in the IP routing table. Because there is a one-to-one correlation between FIB entries and routing table entries, the FIB contains all known routes and eliminates the need for route cache maintenance that is associated with earlier switching paths such as fast switching and optimum switching.
Note: In order to view the Routing information base (RIB) table, use the "show ip route" command.
To view the Forwarding Information Base (FIB), use the "show ip cef" command. RIB is in Control plane while FIB is in Data plane.
QUESTION NO: 5
Which statement about multicast RPs is true?
A. RPs are required for protocol independent multicast sparse mode and dense mode.
B. By default, the RP is needed only to start new sessions with sources and receivers.
C. By default, the RP is needed periodically to maintain sessions with sources and receivers
D. RPs are required only when using protocol independent multicast dense mode.
Answer: B
Explanation:
A rendezvous point (RP) is required only in networks running Protocol Independent Multicast sparse mode (PIM-SM).
By default, the RP is needed only to start new sessions with sources and receivers.
Reference:
https://www.cisco.com/c/en/us/td/docs/ios/solutions_docs/ip_multicast/White_papers/rps.html
For your information, in PIM-SM, only network segments with active receivers that have explicitly requested multicast data will be forwarded the traffic. This method of delivering multicast data is in contrast to the PIM dense mode (PIM-DM) model. In PIM-DM, multicast traffic is initially flooded to all segments of the network. Routers that have no downstream neighbors or directly connected receivers prune back the unwanted traffic.
Because our materials not only has better quality than any other same learn products, but also can guarantee that you can pass the Amazon SOA-C02 exam with ease. We promise you will get high passing mark with our valid CompTIA N10-009 exam torrent and your money will be back to your account if you failed exam with our study materials. SAP C_S4FCF_2023 - The first one is downloading efficiency. With our Microsoft AZ-500 study materials, all of your study can be completed on your computers because we have developed a kind of software which includes all the knowledge of the exam. SAP C_SAC_2402 - We understand your drive of the certificate, so you have a focus already and that is a good start.
Updated: May 28, 2022