Why not have a try? Our 350-401 Dumps Vce exam questions are related to test standards and are made in the form of actual tests. Whether you are newbie or experienced exam candidates, our 350-401 Dumps Vce study guide will relieve you of tremendous pressure and help you conquer the difficulties with efficiency. If there is new information about the exam, you will receive an email about the newest information about the 350-401 Dumps Vce learning dumps. We can promise that you will never miss the important information about the exam. With our 350-401 Dumps Vce exam questions, you will easily get the favor of executives and successfully enter the gates of famous companies.
CCNP Enterprise 350-401 Now, people are blundering.
To satisfy the goals of exam candidates, we created the high quality and high accuracy 350-401 - Implementing Cisco Enterprise Network Core Technologies (350-401 ENCOR) Dumps Vce real materials for you. Then you can go to everywhere without carrying your computers. For it also supports the offline practice.
We are sure you can seep great deal of knowledge from our 350-401 Dumps Vce study prep in preference to other materials obviously. Our 350-401 Dumps Vce practice materials have variant kinds including PDF, app and software versions. As 350-401 Dumps Vce exam questions with high prestige and esteem in the market, we hold sturdy faith for you.
Cisco 350-401 Dumps Vce - So your error can be corrected quickly.
The optimization of 350-401 Dumps Vce training questions is very much in need of your opinion. If you find any problems during use, you can give us feedback. We will give you some benefits as a thank you. You will get a chance to update the system of 350-401 Dumps Vce real exam for free. Of course, we really hope that you can make some good suggestions after using our 350-401 Dumps Vce study materials. We hope to grow with you and help you get more success in your life.
Many students often complain that they cannot purchase counseling materials suitable for themselves. A lot of that stuff was thrown away as soon as it came back.
350-401 PDF DEMO:
QUESTION NO: 1
Refer to the exhibit. A port channel is configured between SW2 and SW3. SW2 is not running a
Cisco operating system. When all physical connections are mode, the port channel does not establish.
Based on the configuration excerpt of SW3, what is the cause of the problem?
A. The port-channel interface lead balance should be set to src-mac
B. The port-channel trunk is not allowing the native VLAN.
C. The port-channel should be set to auto.
D. The port channel on SW2 is using an incompatible protocol.
Answer: D
Explanation:
The Cisco switch was configured with PAgP, which is a Cisco proprietary protocol so non-Cisco switch could not communicate.
QUESTION NO: 2
Which technology provides a secure communication channel for all traffic at Layer 2 of the OSI model?
A. IPsec
B. Cisco Trustsec
C. MACsec
D. SSL
Answer: C
Explanation:
MACsec, defined in 802.1AE, provides MAC-layer encryption over wired networks by using out- of
-band methods for encryption keying. The MACsec Key Agreement (MKA) Protocol provides the required session keys and manages the required encryption keys. MKA and MACsec are implemented after successful authentication using the 802.1x Extensible Authentication Protocol (EAP-TLS) or Pre
Shared Key (PSK) framework.
A switch using MACsec accepts either MACsec or non-MACsec frames, depending on the policy associated with the MKA peer. MACsec frames are encrypted and protected with an integrity check value (ICV). When the switch receives frames from the MKA peer, it decrypts them and calculates the correct ICV by using session keys provided by MKA. The switch compares that ICV to the ICV within the frame. If they are not identical, the frame is dropped. The switch also encrypts and adds an ICV to any frames sent over the secured port (the access point used to provide the secure MAC service to a
MKA peer) using the current session key.
Reference: https://www.cisco.com/c/en/us/td/docs/switches/lan/catalyst9300/software/release/16-
9/configuration_guide/sec/b_169_sec_9300_cg/macsec_encryption.html
Note: Cisco Trustsec is the solution which includes MACsec.
QUESTION NO: 3
Which statement about multicast RPs is true?
A. RPs are required for protocol independent multicast sparse mode and dense mode.
B. By default, the RP is needed only to start new sessions with sources and receivers.
C. By default, the RP is needed periodically to maintain sessions with sources and receivers
D. RPs are required only when using protocol independent multicast dense mode.
Answer: B
Explanation:
A rendezvous point (RP) is required only in networks running Protocol Independent Multicast sparse mode (PIM-SM).
By default, the RP is needed only to start new sessions with sources and receivers.
Reference:
https://www.cisco.com/c/en/us/td/docs/ios/solutions_docs/ip_multicast/White_papers/rps.html
For your information, in PIM-SM, only network segments with active receivers that have explicitly requested multicast data will be forwarded the traffic. This method of delivering multicast data is in contrast to the PIM dense mode (PIM-DM) model. In PIM-DM, multicast traffic is initially flooded to all segments of the network. Routers that have no downstream neighbors or directly connected receivers prune back the unwanted traffic.
QUESTION NO: 4
To increase total throughput and redundancy on the links between the wireless controller and switch, the customer enabled LAG on the wireless controller.
Which EtherChannel mode must be configured on the switch to allow the WLC to connect?
A. Active
B. On
C. Auto
D. Passive
Answer: B
Explanation:
Restrictions for Link Aggregation:
You can bundle all eight ports on a Cisco 5508 Controller into a single link.
Terminating on two different modules within a single Catalyst 6500 series switch provides redundancy and ensures that connectivity between the switch and the controller is maintained when one module fails. The controller's port 1 is connected to Gigabit interface 3/1, and the controller's port 2 is connected to Gigabit interface 2/1 on the Catalyst 6500 series switch. Both switch ports are assigned to the same channel group.
LAG requires the EtherChannel to be configured for 'mode on' on both the controller and the Catalyst switch.
Once the EtherChannel is configured as on at both ends of the link, the Catalyst switch should not be configured for either Link Aggregation Control Protocol (LACP) or Cisco proprietary Port Aggregation
Protocol (PAgP) but be set unconditionally to LAG. Because no channel negotiation is done between the controller and the switch, the controller does not answer to negotiation frames and the LAG is not formed if a dynamic form of LAG is set on the switch. Additionally, LACP and PAgP are not supported on the controller.
If the recommended load-balancing method cannot be configured on the Catalyst switch, then configure the LAG connection as a single member link or disable LAG on the controller.
https://www.cisco.com/c/en/us/td/docs/wireless/controller/7-5/configuration- guide/b_cg75/b_cg75_chapter_0100010.html
QUESTION NO: 5
Which access controls list allows only TCP traffic with a destination port range of 22-433, excluding port 80?
A. Deny tcp any any ne 80
Permit tcp any any range 22 443
B. Permit tcp any any ne 80
C. Permit tco any any range 22 443
Deny tcp any any eq 80
D. Deny tcp any any eq 80
Permit tco any any gt 21 it 444
Answer: D
Microsoft AZ-104-KR - Our passing rate may be the most attractive factor for you. And our pass rate of the Fortinet NSE7_LED-7.0 training engine is high as 98% to 100%, it is the data that proved and tested by our loyal customers. SAP C-BW4H-2404 - If you are not working hard, you will lose a lot of opportunities! The passing rate is the best test for quality of our Juniper JN0-252 study materials. Cisco 500-490 exam prep sincerely hopes that you can achieve your goals and realize your dreams.
Updated: May 28, 2022