Our 200-301 Simulator Online study materials have included all significant knowledge about the exam. So you do not need to pick out the important points by yourself. Also, our 200-301 Simulator Online practice engine can greatly shorten your preparation time of the exam. Our 200-301 Simulator Online exam questions have helped a large number of candidates pass the 200-301 Simulator Online exam yet. Hope you can join us, and we work together to create a miracle. You will enjoy learning on our 200-301 Simulator Online exam questions for its wonderful and latest design with the latest technologies applied.
CCNA 200-301 It is quite convenient.
CCNA 200-301 Simulator Online - Cisco Certified Network Associate Exam Our study materials come to your help. If you are better, you will have a more relaxed life. Test 200-301 Forum guide materials allow you to increase the efficiency of your work.
our 200-301 Simulator Online study materials will also save your time and energy in well-targeted learning as we are going to make everything done in order that you can stay focused in learning our 200-301 Simulator Online study materials without worries behind. We are so honored and pleased to be able to read our detailed introduction and we will try our best to enable you a better understanding of our 200-301 Simulator Online study materials better.
Our Cisco 200-301 Simulator Online actual test guide can give you some help.
Before you decide to buy Omgzlook of Cisco 200-301 Simulator Online exam questions, you will have a free part of the questions and answers as a trial. So that you will know the quality of the Omgzlook of Cisco 200-301 Simulator Online exam training materials. The Cisco 200-301 Simulator Online exam of Omgzlook is the best choice for you.
The future is really beautiful, but now, taking a crucial step is even more important! Buy 200-301 Simulator Online exam prep and stick with it.
200-301 PDF DEMO:
QUESTION NO: 1
Which statement about Link Aggregation when implemented on a Cisco Wireless LAN
Controller is true?
A. One functional physical port is needed to pass client traffic
B. The EtherChannel must be configured in "mode active"
C. When enabled the WLC bandwidth drops to 500 Mbps
D. To pass client traffic two or more ports must be configured.
Answer: A
Explanation:
Link aggregation (LAG) is a partial implementation of the 802.3ad port aggregation standard. It bundles all of the controller's distribution system ports into a single 802.3ad port channel.
Restriction for Link aggregation:
- LAG requires the EtherChannel to be configured for `mode on' on both the controller and the
Catalyst switch -> Answer B is not correct.
- If the recommended load-balancing method cannot be configured on the Catalyst switch, then configure the LAG connection as a single member link or disable LAG on the controller -> Answer A is not correct while answer D is correct.
Reference: https://www.cisco.com/c/en/us/td/docs/wireless/controller/7-5/configuration- guide/b_cg75/ b_cg75_chapter_0100010.html
QUESTION NO: 2
Refer to the exhibit. C-router is to be used as a "router-on-a-stick" to route between the
VLANs.
All the interfaces have been properly configured and IP routing is operational. The hosts in the VLANs have been configured with the appropriate default gateway.
What is true about this configuration?
A. These commands need to be added to the configuration:
C-router(config)# router rip
C-router(config-router)# network 172.19.0.0
B. These commands need to be added to the configuration:
C-router(config)# router ospf 1
C-router(config-router)# network 172.19.0.0 0.0.3.255 area 0
C. These commands need to be added to the configuration:
C-router(config)# router eigrp 123
C-router(config-router)# network 172.19.0.0
D. No further routing configuration is required.
Answer: D
Explanation:
Since all the same router (C-router) is the default gateway for all three VLANs, all traffic destined to a different VLAN will be sent to the C-router. The C-router will have knowledge of all three networks since they will appear as directly connected in the routing table. Since the C-router already knows how to get to all three networks, no routing protocols need to be configured.
QUESTION NO: 3
Drag and Drop Question
Drag and drop the WLAN components from the left onto the correct descriptions on the right.
Answer:
Explanation:
The service port can be used management purposes, primarily for out-of-band management.
However, AP management traffic is not possible across the service port. In most cases, the service port is used as a "last resort" means of accessing the controller GUI for management purposes. For example, in the case where the system distribution ports on the controller are down or their communication to the wired network is otherwise degraded.
A dynamic interface with the Dynamic AP Management option enabled is used as the tunnel source for packets from the controller to the access point and as the destination for CAPWAP packets from the access point to the controller.
The virtual interface is used to support mobility management, Dynamic Host Configuration Protocol
(DHCP) relay, and embedded Layer 3 security such as guest web authentication. It also maintains the
DNS gateway host name used by Layer 3 security and mobility managers to verify the source of certificates when Layer 3 web authorization is enabled.
Reference: https://www.cisco.com/c/en/us/td/docs/wireless/controller/8-5/config- guide/b_cg85/ports_and_interfaces.html
QUESTION NO: 4
A router running EIGRP has learned the same route from two different paths. Which parameter does the router use to select the best path?
A. administrative distance
B. as-path
C. metric
D. cost
Answer: C
Explanation:
If a router learns two different paths for the same network from the same routing protocol, it has to decide which route is better and will be placed in the routing table. Metric is the measure used to decide which route is better (lower number is better). Each routing protocol uses its own metric.
For example, RIP uses hop counts as a metric, while OSPF uses cost.
https://study-ccna.com/administrative-distance-metric/
QUESTION NO: 5
Which two tasks must be performed to configure NTP to a trusted server in client mode on a single network device? (Choose two)
A. Verify the time zone.
B. Disable NTP broadcasts
C. Set the NTP server private key
D. Specify the IP address of the NTP server
E. Enable NTP authentication.
Answer: D,E
Explanation:
To configure authentication, perform this task in privileged mode:
Step 1: Configure an authentication key pair for NTP and specify whether the key will be trusted or untrusted.
Step 2: Set the IP address of the NTP server and the public key.
Step 3: Enable NTP client mode.
Step 4: Enable NTP authentication.
Step 5: Verify the NTP configuration.
Reference: https://www.cisco.com/c/en/us/td/docs/switches/lan/catalyst4000/8-
2glx/configuration/guide/ ntp.html
Amazon SAP-C02 - And the materials we have are very cheap. Network Appliance NS0-521 - Anyway, after your payment, you can enjoy the one-year free update service with our guarantee. ISQI CPSA-FL - It includes questions and answers, and issimilar with the real exam questions. Besides, the price of our AACN CCRN-Adult learning guide is very favourable even the students can afford it. DAMA CDMP-RMD - With this certification, you can light up your heart light in your life.
Updated: May 28, 2022