私たちの350-401認証試験参考資料は十年以上にわたり、専門家が何度も練習して、作られました。あなたに高品質で、全面的な350-401認証試験参考資料を提供することは私たちの責任です。私たちより、350-401認証試験試験を知る人はいません。 我々350-401認証試験問題集の通過率は高いので、90％の合格率を保証します。あなたは弊社の高品質Cisco 350-401認証試験試験資料を利用して、一回に試験に合格します。 弊社の無料なサンプルを遠慮なくダウンロードしてください。
CCNP Enterprise 350-401 暇の時間を利用して勉強します。
CCNP Enterprise 350-401認証試験 - Implementing Cisco Enterprise Network Core Technologies (350-401 ENCOR) こうして、弊社の商品はどのくらいあなたの力になるのはよく分かっています。 そして、350-401 復習内容試験参考書の問題は本当の試験問題とだいたい同じことであるとわかります。350-401 復習内容試験参考書があれば,ほかの試験参考書を勉強する必要がないです。
Omgzlookは頼りが強い上にサービスもよくて、もし試験に失敗したら全額で返金いたしてまた一年の無料なアップデートいたします。
Cisco 350-401認証試験 - きっと君に失望させないと信じています。
Ciscoの350-401認証試験認証試験を選んだ人々が一層多くなります。350-401認証試験試験がユニバーサルになりましたから、あなたはOmgzlook のCiscoの350-401認証試験試験問題と解答￥を利用したらきっと試験に合格するができます。それに、あなたに極大な便利と快適をもたらせます。実践の検査に何度も合格したこのサイトは試験問題と解答を提供しています。皆様が知っているように、OmgzlookはCiscoの350-401認証試験試験問題と解答を提供している専門的なサイトです。
我々は受験生の皆様により高いスピードを持っているかつ効率的なサービスを提供することにずっと力を尽くしていますから、あなたが貴重な時間を節約することに助けを差し上げます。Omgzlook Ciscoの350-401認証試験試験問題集はあなたに問題と解答に含まれている大量なテストガイドを提供しています。
350-401 PDF DEMO:
QUESTION NO: 1
What is the difference between a RIB and a FIB?
A. The FIB is populated based on RIB content
B. The RIB is used to make IP source prefix-based switching decisions
C. The RIB maintains a mirror image of the FIB
D. The FIB is where all IP routing information is stored
Answer: A
Explanation:
CEF uses a Forwarding Information Base (FIB) to make IP destination prefix-based switching decisions.
The FIB is conceptually similar to a routing table or information base. It maintains a mirror image of the forwarding information contained in the IP routing table. When routing or topology changes occur in the network, the IP routing table is updated, and those changes are reflected in the FIB. The
FIB maintains next-hop address information based on the information in the IP routing table. Because there is a one-to-one correlation between FIB entries and routing table entries, the FIB contains all known routes and eliminates the need for route cache maintenance that is associated with earlier switching paths such as fast switching and optimum switching.
Note: In order to view the Routing information base (RIB) table, use the "show ip route" command.
To view the Forwarding Information Base (FIB), use the "show ip cef" command. RIB is in Control plane while FIB is in Data plane.
QUESTION NO: 2
Which feature does Cisco TrustSec use to provide scalable, secure communication throughout a network?
A. security group tag number assigned to each user on a switch
B. security group tag ACL assigned to each router on a network
C. security group tag ACL assigned to each port on a switch
D. security group tag number assigned to each port on a network
Answer: D
Explanation:
Cisco TrustSec uses tags to represent logical group privilege. This tag, called a Security Group Tag
(SGT), is used in access policies. The SGT is understood and is used to enforce traffic by Cisco switches, routers and firewalls . Cisco TrustSec is defined in three phases: classification, propagation and enforcement.
When users and devices connect to a network, the network assigns a specific security group.
This process is called classification. Classification can be based on the results of the authentication or by associating the SGT with an IP, VLAN, or port-profile (-> Answer A and answer C are not correct as they say "assigned ... on a switch" only. Answer D is not correct either as it says "assigned to each router").
QUESTION NO: 3
To increase total throughput and redundancy on the links between the wireless controller and switch, the customer enabled LAG on the wireless controller.
Which EtherChannel mode must be configured on the switch to allow the WLC to connect?
A. Active
B. On
C. Auto
D. Passive
Answer: B
Explanation:
Restrictions for Link Aggregation:
You can bundle all eight ports on a Cisco 5508 Controller into a single link.
Terminating on two different modules within a single Catalyst 6500 series switch provides redundancy and ensures that connectivity between the switch and the controller is maintained when one module fails. The controller's port 1 is connected to Gigabit interface 3/1, and the controller's port 2 is connected to Gigabit interface 2/1 on the Catalyst 6500 series switch. Both switch ports are assigned to the same channel group.
LAG requires the EtherChannel to be configured for 'mode on' on both the controller and the Catalyst switch.
Once the EtherChannel is configured as on at both ends of the link, the Catalyst switch should not be configured for either Link Aggregation Control Protocol (LACP) or Cisco proprietary Port Aggregation
Protocol (PAgP) but be set unconditionally to LAG. Because no channel negotiation is done between the controller and the switch, the controller does not answer to negotiation frames and the LAG is not formed if a dynamic form of LAG is set on the switch. Additionally, LACP and PAgP are not supported on the controller.
If the recommended load-balancing method cannot be configured on the Catalyst switch, then configure the LAG connection as a single member link or disable LAG on the controller.
https://www.cisco.com/c/en/us/td/docs/wireless/controller/7-5/configuration- guide/b_cg75/b_cg75_chapter_0100010.html
QUESTION NO: 4
Which technology provides a secure communication channel for all traffic at Layer 2 of the OSI model?
A. IPsec
B. Cisco Trustsec
C. MACsec
D. SSL
Answer: C
Explanation:
MACsec, defined in 802.1AE, provides MAC-layer encryption over wired networks by using out- of
-band methods for encryption keying. The MACsec Key Agreement (MKA) Protocol provides the required session keys and manages the required encryption keys. MKA and MACsec are implemented after successful authentication using the 802.1x Extensible Authentication Protocol (EAP-TLS) or Pre
Shared Key (PSK) framework.
A switch using MACsec accepts either MACsec or non-MACsec frames, depending on the policy associated with the MKA peer. MACsec frames are encrypted and protected with an integrity check value (ICV). When the switch receives frames from the MKA peer, it decrypts them and calculates the correct ICV by using session keys provided by MKA. The switch compares that ICV to the ICV within the frame. If they are not identical, the frame is dropped. The switch also encrypts and adds an ICV to any frames sent over the secured port (the access point used to provide the secure MAC service to a
MKA peer) using the current session key.
Reference: https://www.cisco.com/c/en/us/td/docs/switches/lan/catalyst9300/software/release/16-
9/configuration_guide/sec/b_169_sec_9300_cg/macsec_encryption.html
Note: Cisco Trustsec is the solution which includes MACsec.
QUESTION NO: 5
Refer to the exhibit. A port channel is configured between SW2 and SW3. SW2 is not running a
Cisco operating system. When all physical connections are mode, the port channel does not establish.
Based on the configuration excerpt of SW3, what is the cause of the problem?
A. The port-channel interface lead balance should be set to src-mac
B. The port-channel trunk is not allowing the native VLAN.
C. The port-channel should be set to auto.
D. The port channel on SW2 is using an incompatible protocol.
Answer: D
Explanation:
The Cisco switch was configured with PAgP, which is a Cisco proprietary protocol so non-Cisco switch could not communicate.
CiscoのDell D-DLM-A-01認定試験に受かる勉強サイトを探しているのなら、Omgzlookはあなたにとって一番良い選択です。 OmgzlookのCiscoのCisco 350-601Jトレーニング資料即ち問題と解答をダウンロードする限り、気楽に試験に受かることができるようになります。 Cisco 300-715 - この試験に合格したら、あなたのITキャリアには明るい未来があるようになります。 Cisco 200-301 - Omgzlookはあなたが首尾よく試験に合格することを助けるだけでなく、あなたの知識と技能を向上させることもできます。 Cisco 700-695 - Omgzlookを選んだら、成功の手を握ることがきるようになります。
Updated: May 28, 2022