Omgzlookはきみの貴重な時間を節約するだけでなく、 安心で順調に試験に合格するのを保証します。Omgzlookは専門のIT業界での評判が高くて、あなたがインターネットでOmgzlookの部分のCisco 350-401認定資格「Implementing Cisco Enterprise Network Core Technologies (350-401 ENCOR)」資料を無料でダウンロードして、弊社の正確率を確認してください。弊社の商品が好きなのは弊社のたのしいです。 躊躇わなくて、Omgzlookサイト情報を早く了解して、あなたに試験合格を助かってあげますようにお願いいたします。周りの多くの人は全部Cisco 350-401認定資格資格認定試験にパースしまして、彼らはどのようにできましたか。 Omgzlook を選択して１００％の合格率を確保することができて、もし試験に失敗したら、Omgzlookが全額で返金いたします。
CCNP Enterprise 350-401 それも我々が全てのお客様に対する約束です。
Omgzlookの350-401 - Implementing Cisco Enterprise Network Core Technologies (350-401 ENCOR)認定資格問題集は多くの受験生に検証されたものですから、高い成功率を保証できます。 Omgzlookのトレーニング資料は大勢な受験生に証明されたもので、国際的に他のサイトをずっと先んじています。Ciscoの350-401 関連復習問題集認定試験に合格したいのなら、Omgzlookが提供したCiscoの350-401 関連復習問題集トレーニング資料をショッピングカートに入れましょう。
OmgzlookのITエリートたちは彼らの専門的な目で、最新的なCiscoの350-401認定資格試験トレーニング資料に注目していて、うちのCiscoの350-401認定資格問題集の高い正確性を保証するのです。もし君はいささかな心配することがあるなら、あなたはうちの商品を購入する前に、Omgzlookは無料でサンプルを提供することができます。なぜ受験生のほとんどはOmgzlookを選んだのですか。
Cisco 350-401認定資格 - それはあなたが夢を実現することを助けられます。
常々、時間とお金ばかり効果がないです。正しい方法は大切です。我々Omgzlookは一番効果的な方法を探してあなたにCiscoの350-401認定資格試験に合格させます。弊社のCiscoの350-401認定資格ソフトを購入するのを決めるとき、我々は各方面であなたに保障を提供します。購入した前の無料の試み、購入するときのお支払いへの保障、購入した一年間の無料更新Ciscoの350-401認定資格試験に失敗した全額での返金…これらは我々のお客様への承諾です。
試験に合格してから、あなたのキャリアは美しい時期を迎えるようになります。偉大な事業を実現するために信心を持つ必要があります。
350-401 PDF DEMO:
QUESTION NO: 1
To increase total throughput and redundancy on the links between the wireless controller and switch, the customer enabled LAG on the wireless controller.
Which EtherChannel mode must be configured on the switch to allow the WLC to connect?
A. Active
B. On
C. Auto
D. Passive
Answer: B
Explanation:
Restrictions for Link Aggregation:
You can bundle all eight ports on a Cisco 5508 Controller into a single link.
Terminating on two different modules within a single Catalyst 6500 series switch provides redundancy and ensures that connectivity between the switch and the controller is maintained when one module fails. The controller's port 1 is connected to Gigabit interface 3/1, and the controller's port 2 is connected to Gigabit interface 2/1 on the Catalyst 6500 series switch. Both switch ports are assigned to the same channel group.
LAG requires the EtherChannel to be configured for 'mode on' on both the controller and the Catalyst switch.
Once the EtherChannel is configured as on at both ends of the link, the Catalyst switch should not be configured for either Link Aggregation Control Protocol (LACP) or Cisco proprietary Port Aggregation
Protocol (PAgP) but be set unconditionally to LAG. Because no channel negotiation is done between the controller and the switch, the controller does not answer to negotiation frames and the LAG is not formed if a dynamic form of LAG is set on the switch. Additionally, LACP and PAgP are not supported on the controller.
If the recommended load-balancing method cannot be configured on the Catalyst switch, then configure the LAG connection as a single member link or disable LAG on the controller.
https://www.cisco.com/c/en/us/td/docs/wireless/controller/7-5/configuration- guide/b_cg75/b_cg75_chapter_0100010.html
QUESTION NO: 2
Which technology provides a secure communication channel for all traffic at Layer 2 of the OSI model?
A. IPsec
B. Cisco Trustsec
C. MACsec
D. SSL
Answer: C
Explanation:
MACsec, defined in 802.1AE, provides MAC-layer encryption over wired networks by using out- of
-band methods for encryption keying. The MACsec Key Agreement (MKA) Protocol provides the required session keys and manages the required encryption keys. MKA and MACsec are implemented after successful authentication using the 802.1x Extensible Authentication Protocol (EAP-TLS) or Pre
Shared Key (PSK) framework.
A switch using MACsec accepts either MACsec or non-MACsec frames, depending on the policy associated with the MKA peer. MACsec frames are encrypted and protected with an integrity check value (ICV). When the switch receives frames from the MKA peer, it decrypts them and calculates the correct ICV by using session keys provided by MKA. The switch compares that ICV to the ICV within the frame. If they are not identical, the frame is dropped. The switch also encrypts and adds an ICV to any frames sent over the secured port (the access point used to provide the secure MAC service to a
MKA peer) using the current session key.
Reference: https://www.cisco.com/c/en/us/td/docs/switches/lan/catalyst9300/software/release/16-
9/configuration_guide/sec/b_169_sec_9300_cg/macsec_encryption.html
Note: Cisco Trustsec is the solution which includes MACsec.
QUESTION NO: 3
What is the difference between a RIB and a FIB?
A. The FIB is populated based on RIB content
B. The RIB is used to make IP source prefix-based switching decisions
C. The RIB maintains a mirror image of the FIB
D. The FIB is where all IP routing information is stored
Answer: A
Explanation:
CEF uses a Forwarding Information Base (FIB) to make IP destination prefix-based switching decisions.
The FIB is conceptually similar to a routing table or information base. It maintains a mirror image of the forwarding information contained in the IP routing table. When routing or topology changes occur in the network, the IP routing table is updated, and those changes are reflected in the FIB. The
FIB maintains next-hop address information based on the information in the IP routing table. Because there is a one-to-one correlation between FIB entries and routing table entries, the FIB contains all known routes and eliminates the need for route cache maintenance that is associated with earlier switching paths such as fast switching and optimum switching.
Note: In order to view the Routing information base (RIB) table, use the "show ip route" command.
To view the Forwarding Information Base (FIB), use the "show ip cef" command. RIB is in Control plane while FIB is in Data plane.
QUESTION NO: 4
Refer to the exhibit. A port channel is configured between SW2 and SW3. SW2 is not running a
Cisco operating system. When all physical connections are mode, the port channel does not establish.
Based on the configuration excerpt of SW3, what is the cause of the problem?
A. The port-channel interface lead balance should be set to src-mac
B. The port-channel trunk is not allowing the native VLAN.
C. The port-channel should be set to auto.
D. The port channel on SW2 is using an incompatible protocol.
Answer: D
Explanation:
The Cisco switch was configured with PAgP, which is a Cisco proprietary protocol so non-Cisco switch could not communicate.
QUESTION NO: 5
Which statement about multicast RPs is true?
A. RPs are required for protocol independent multicast sparse mode and dense mode.
B. By default, the RP is needed only to start new sessions with sources and receivers.
C. By default, the RP is needed periodically to maintain sessions with sources and receivers
D. RPs are required only when using protocol independent multicast dense mode.
Answer: B
Explanation:
A rendezvous point (RP) is required only in networks running Protocol Independent Multicast sparse mode (PIM-SM).
By default, the RP is needed only to start new sessions with sources and receivers.
Reference:
https://www.cisco.com/c/en/us/td/docs/ios/solutions_docs/ip_multicast/White_papers/rps.html
For your information, in PIM-SM, only network segments with active receivers that have explicitly requested multicast data will be forwarded the traffic. This method of delivering multicast data is in contrast to the PIM dense mode (PIM-DM) model. In PIM-DM, multicast traffic is initially flooded to all segments of the network. Routers that have no downstream neighbors or directly connected receivers prune back the unwanted traffic.
Cisco 350-201 - できるだけ100％の通過率を保証使用にしています。 そして、ソフトウェア版のEMC D-RP-DY-A-24問題集は実際試験の雰囲気を感じさせることができます。 ただ、社会に入るIT卒業生たちは自分能力の不足で、Microsoft SC-900J試験向けの仕事を探すのを悩んでいますか？それでは、弊社のCiscoのMicrosoft SC-900J練習問題を選んで実用能力を速く高め、自分を充実させます。 OmgzlookのSAP C_ARCON_2404試験参考書は他のSAP C_ARCON_2404試験に関連するする参考書よりずっと良いです。 OmgzlookのCisco EMC D-VXB-DY-A-24問題集は専門家たちが数年間で過去のデータから分析して作成されて、試験にカバーする範囲は広くて、受験生の皆様のお金と時間を節約します。
Updated: May 28, 2022