現在IT技術会社に通勤しているあなたは、Ciscoの350-401認定試験試験認定を取得しましたか？350-401認定試験試験認定は給料の増加とジョブのプロモーションに役立ちます。短時間で350-401認定試験試験に一発合格したいなら、我々社のCiscoの350-401認定試験資料を参考しましょう。また、350-401認定試験問題集に疑問があると、メールで問い合わせてください。 お客様の満足は我々の進む力です。我々社のCisco 350-401認定試験問題集を使用して試験に合格しないで全額での返金を承諾するのは弊社の商品に不自信ではなく、行為でもって我々の誠意を示します。 人によって目標が違いますが、あなたにCisco 350-401認定試験試験に順調に合格できるのは我々の共同の目標です。
CCNP Enterprise 350-401 早くOmgzlookの問題集を君の手に入れましょう。
CCNP Enterprise 350-401認定試験 - Implementing Cisco Enterprise Network Core Technologies (350-401 ENCOR) たくさんのひとは弊社の商品を使って、試験に順調に合格しました。 君が後悔しないようにもっと少ないお金を使って大きな良い成果を取得するためにOmgzlookを選択してください。Omgzlookはまた一年間に無料なサービスを更新いたします。
この情報の時代の中に、たくさんのIT機構はCiscoの350-401認定試験認定試験に関する教育資料がありますけれども、受験生がこれらのサイトを通じて詳細な資料を調べられなくて、対応性がなくて受験生の注意 に惹かれなりません。
Cisco 350-401認定試験 - そうすると、我々の信頼性をテストできます。
なぜ受験生のほとんどはOmgzlookを選んだのですか。それはOmgzlookがすごく便利で、広い通用性があるからです。OmgzlookのITエリートたちは彼らの専門的な目で、最新的なCiscoの350-401認定試験試験トレーニング資料に注目していて、うちのCiscoの350-401認定試験問題集の高い正確性を保証するのです。もし君はいささかな心配することがあるなら、あなたはうちの商品を購入する前に、Omgzlookは無料でサンプルを提供することができます。
インターネットでこんな高品質の資料を提供するサイトはOmgzlookしかないです。OmgzlookのCiscoの350-401認定試験試験トレーニング資料はIT認証試験を受ける人々の必需品です。
350-401 PDF DEMO:
QUESTION NO: 1
Refer to the exhibit. A port channel is configured between SW2 and SW3. SW2 is not running a
Cisco operating system. When all physical connections are mode, the port channel does not establish.
Based on the configuration excerpt of SW3, what is the cause of the problem?
A. The port-channel interface lead balance should be set to src-mac
B. The port-channel trunk is not allowing the native VLAN.
C. The port-channel should be set to auto.
D. The port channel on SW2 is using an incompatible protocol.
Answer: D
Explanation:
The Cisco switch was configured with PAgP, which is a Cisco proprietary protocol so non-Cisco switch could not communicate.
QUESTION NO: 2
Which statement about multicast RPs is true?
A. RPs are required for protocol independent multicast sparse mode and dense mode.
B. By default, the RP is needed only to start new sessions with sources and receivers.
C. By default, the RP is needed periodically to maintain sessions with sources and receivers
D. RPs are required only when using protocol independent multicast dense mode.
Answer: B
Explanation:
A rendezvous point (RP) is required only in networks running Protocol Independent Multicast sparse mode (PIM-SM).
By default, the RP is needed only to start new sessions with sources and receivers.
Reference:
https://www.cisco.com/c/en/us/td/docs/ios/solutions_docs/ip_multicast/White_papers/rps.html
For your information, in PIM-SM, only network segments with active receivers that have explicitly requested multicast data will be forwarded the traffic. This method of delivering multicast data is in contrast to the PIM dense mode (PIM-DM) model. In PIM-DM, multicast traffic is initially flooded to all segments of the network. Routers that have no downstream neighbors or directly connected receivers prune back the unwanted traffic.
QUESTION NO: 3
Which technology provides a secure communication channel for all traffic at Layer 2 of the OSI model?
A. IPsec
B. Cisco Trustsec
C. MACsec
D. SSL
Answer: C
Explanation:
MACsec, defined in 802.1AE, provides MAC-layer encryption over wired networks by using out- of
-band methods for encryption keying. The MACsec Key Agreement (MKA) Protocol provides the required session keys and manages the required encryption keys. MKA and MACsec are implemented after successful authentication using the 802.1x Extensible Authentication Protocol (EAP-TLS) or Pre
Shared Key (PSK) framework.
A switch using MACsec accepts either MACsec or non-MACsec frames, depending on the policy associated with the MKA peer. MACsec frames are encrypted and protected with an integrity check value (ICV). When the switch receives frames from the MKA peer, it decrypts them and calculates the correct ICV by using session keys provided by MKA. The switch compares that ICV to the ICV within the frame. If they are not identical, the frame is dropped. The switch also encrypts and adds an ICV to any frames sent over the secured port (the access point used to provide the secure MAC service to a
MKA peer) using the current session key.
Reference: https://www.cisco.com/c/en/us/td/docs/switches/lan/catalyst9300/software/release/16-
9/configuration_guide/sec/b_169_sec_9300_cg/macsec_encryption.html
Note: Cisco Trustsec is the solution which includes MACsec.
QUESTION NO: 4
To increase total throughput and redundancy on the links between the wireless controller and switch, the customer enabled LAG on the wireless controller.
Which EtherChannel mode must be configured on the switch to allow the WLC to connect?
A. Active
B. On
C. Auto
D. Passive
Answer: B
Explanation:
Restrictions for Link Aggregation:
You can bundle all eight ports on a Cisco 5508 Controller into a single link.
Terminating on two different modules within a single Catalyst 6500 series switch provides redundancy and ensures that connectivity between the switch and the controller is maintained when one module fails. The controller's port 1 is connected to Gigabit interface 3/1, and the controller's port 2 is connected to Gigabit interface 2/1 on the Catalyst 6500 series switch. Both switch ports are assigned to the same channel group.
LAG requires the EtherChannel to be configured for 'mode on' on both the controller and the Catalyst switch.
Once the EtherChannel is configured as on at both ends of the link, the Catalyst switch should not be configured for either Link Aggregation Control Protocol (LACP) or Cisco proprietary Port Aggregation
Protocol (PAgP) but be set unconditionally to LAG. Because no channel negotiation is done between the controller and the switch, the controller does not answer to negotiation frames and the LAG is not formed if a dynamic form of LAG is set on the switch. Additionally, LACP and PAgP are not supported on the controller.
If the recommended load-balancing method cannot be configured on the Catalyst switch, then configure the LAG connection as a single member link or disable LAG on the controller.
https://www.cisco.com/c/en/us/td/docs/wireless/controller/7-5/configuration- guide/b_cg75/b_cg75_chapter_0100010.html
QUESTION NO: 5
Which access controls list allows only TCP traffic with a destination port range of 22-433, excluding port 80?
A. Deny tcp any any ne 80
Permit tcp any any range 22 443
B. Permit tcp any any ne 80
C. Permit tco any any range 22 443
Deny tcp any any eq 80
D. Deny tcp any any eq 80
Permit tco any any gt 21 it 444
Answer: D
OmgzlookのCiscoのCIMA CIMAPRO19-CS3-1問題集を購入するなら、君がCiscoのCIMA CIMAPRO19-CS3-1認定試験に合格する率は１００パーセントです。 CheckPoint 156-587 - この試験の認証資格を取ったら、あなたは多くの利益を得ることができます。 我々Omgzlookは一番効果的な方法を探してあなたにCiscoのOracle 1z0-1085-24試験に合格させます。 SailPoint IdentityIQ-Engineer - ですから、心のリラックスした状態で試験に出る問題を対応することができ、あなたの正常なレベルをプレイすることもできます。 Omgzlookは多くの受験生を助けて彼らにCiscoのScrum PAL-I試験に合格させることができるのは我々専門的なチームがCiscoのScrum PAL-I試験を研究して解答を詳しく分析しますから。
Updated: May 28, 2022