人によって目標が違いますが、あなたにCisco 350-401認定デベロッパー試験に順調に合格できるのは我々の共同の目標です。この目標の達成はあなたがIT技術領域へ行く更なる発展の一歩ですけど、我々社Omgzlook存在するこそすべての意義です。だから、我々社は力の限りで弊社のCisco 350-401認定デベロッパー試験資料を改善し、改革の変更に応じて更新します。 Omgzlookが提供したCiscoの350-401認定デベロッパートレーニング資料は問題と解答に含まれていて、IT技術専門家たちによって開発されたものです。Ciscoの350-401認定デベロッパー認定試験を受けたいのなら、Omgzlookを選ぶのは疑いないことです。 あなたに高品質で、全面的な350-401認定デベロッパー参考資料を提供することは私たちの責任です。
CCNP Enterprise 350-401 弊社の商品が好きなのは弊社のたのしいです。
OmgzlookのCiscoの350-401 - Implementing Cisco Enterprise Network Core Technologies (350-401 ENCOR)認定デベロッパー試験トレーニング資料は間違いなく最高のトレーニング資料ですから、それを選ぶことはあなたにとって最高の選択です。 Omgzlook を選択して１００％の合格率を確保することができて、もし試験に失敗したら、Omgzlookが全額で返金いたします。
あなたは新しい旅を始めることができ、人生の輝かしい実績を実現することができます。他の人の成功を見上げるよりも、自分の成功への努力をしたほうがよいです。OmgzlookのCiscoの350-401認定デベロッパー試験トレーニング資料はあなたの成功への第一歩です。
それはOmgzlookのCisco 350-401認定デベロッパー問題集です。
Omgzlook のCiscoの350-401認定デベロッパー問題集はシラバスに従って、それに350-401認定デベロッパー認定試験の実際に従って、あなたがもっとも短い時間で最高かつ最新の情報をもらえるように、弊社はトレーニング資料を常にアップグレードしています。弊社の350-401認定デベロッパーのトレーニング資料を買ったら、一年間の無料更新サービスを差し上げます。もっと長い時間をもらって試験を準備したいのなら、あなたがいつでもサブスクリプションの期間を伸びることができます。
ショートカットを選択し、テクニックを使用するのはより良く成功できるからです。350-401認定デベロッパー認定試験に一発合格できる保障を得たいなら、Omgzlook の350-401認定デベロッパー問題集はあなたにとってユニークな、しかも最良の選択です。
350-401 PDF DEMO:
QUESTION NO: 1
To increase total throughput and redundancy on the links between the wireless controller and switch, the customer enabled LAG on the wireless controller.
Which EtherChannel mode must be configured on the switch to allow the WLC to connect?
A. Active
B. On
C. Auto
D. Passive
Answer: B
Explanation:
Restrictions for Link Aggregation:
You can bundle all eight ports on a Cisco 5508 Controller into a single link.
Terminating on two different modules within a single Catalyst 6500 series switch provides redundancy and ensures that connectivity between the switch and the controller is maintained when one module fails. The controller's port 1 is connected to Gigabit interface 3/1, and the controller's port 2 is connected to Gigabit interface 2/1 on the Catalyst 6500 series switch. Both switch ports are assigned to the same channel group.
LAG requires the EtherChannel to be configured for 'mode on' on both the controller and the Catalyst switch.
Once the EtherChannel is configured as on at both ends of the link, the Catalyst switch should not be configured for either Link Aggregation Control Protocol (LACP) or Cisco proprietary Port Aggregation
Protocol (PAgP) but be set unconditionally to LAG. Because no channel negotiation is done between the controller and the switch, the controller does not answer to negotiation frames and the LAG is not formed if a dynamic form of LAG is set on the switch. Additionally, LACP and PAgP are not supported on the controller.
If the recommended load-balancing method cannot be configured on the Catalyst switch, then configure the LAG connection as a single member link or disable LAG on the controller.
https://www.cisco.com/c/en/us/td/docs/wireless/controller/7-5/configuration- guide/b_cg75/b_cg75_chapter_0100010.html
QUESTION NO: 2
Which technology provides a secure communication channel for all traffic at Layer 2 of the OSI model?
A. IPsec
B. Cisco Trustsec
C. MACsec
D. SSL
Answer: C
Explanation:
MACsec, defined in 802.1AE, provides MAC-layer encryption over wired networks by using out- of
-band methods for encryption keying. The MACsec Key Agreement (MKA) Protocol provides the required session keys and manages the required encryption keys. MKA and MACsec are implemented after successful authentication using the 802.1x Extensible Authentication Protocol (EAP-TLS) or Pre
Shared Key (PSK) framework.
A switch using MACsec accepts either MACsec or non-MACsec frames, depending on the policy associated with the MKA peer. MACsec frames are encrypted and protected with an integrity check value (ICV). When the switch receives frames from the MKA peer, it decrypts them and calculates the correct ICV by using session keys provided by MKA. The switch compares that ICV to the ICV within the frame. If they are not identical, the frame is dropped. The switch also encrypts and adds an ICV to any frames sent over the secured port (the access point used to provide the secure MAC service to a
MKA peer) using the current session key.
Reference: https://www.cisco.com/c/en/us/td/docs/switches/lan/catalyst9300/software/release/16-
9/configuration_guide/sec/b_169_sec_9300_cg/macsec_encryption.html
Note: Cisco Trustsec is the solution which includes MACsec.
QUESTION NO: 3
What is the difference between a RIB and a FIB?
A. The FIB is populated based on RIB content
B. The RIB is used to make IP source prefix-based switching decisions
C. The RIB maintains a mirror image of the FIB
D. The FIB is where all IP routing information is stored
Answer: A
Explanation:
CEF uses a Forwarding Information Base (FIB) to make IP destination prefix-based switching decisions.
The FIB is conceptually similar to a routing table or information base. It maintains a mirror image of the forwarding information contained in the IP routing table. When routing or topology changes occur in the network, the IP routing table is updated, and those changes are reflected in the FIB. The
FIB maintains next-hop address information based on the information in the IP routing table. Because there is a one-to-one correlation between FIB entries and routing table entries, the FIB contains all known routes and eliminates the need for route cache maintenance that is associated with earlier switching paths such as fast switching and optimum switching.
Note: In order to view the Routing information base (RIB) table, use the "show ip route" command.
To view the Forwarding Information Base (FIB), use the "show ip cef" command. RIB is in Control plane while FIB is in Data plane.
QUESTION NO: 4
Refer to the exhibit. A port channel is configured between SW2 and SW3. SW2 is not running a
Cisco operating system. When all physical connections are mode, the port channel does not establish.
Based on the configuration excerpt of SW3, what is the cause of the problem?
A. The port-channel interface lead balance should be set to src-mac
B. The port-channel trunk is not allowing the native VLAN.
C. The port-channel should be set to auto.
D. The port channel on SW2 is using an incompatible protocol.
Answer: D
Explanation:
The Cisco switch was configured with PAgP, which is a Cisco proprietary protocol so non-Cisco switch could not communicate.
QUESTION NO: 5
Which statement about multicast RPs is true?
A. RPs are required for protocol independent multicast sparse mode and dense mode.
B. By default, the RP is needed only to start new sessions with sources and receivers.
C. By default, the RP is needed periodically to maintain sessions with sources and receivers
D. RPs are required only when using protocol independent multicast dense mode.
Answer: B
Explanation:
A rendezvous point (RP) is required only in networks running Protocol Independent Multicast sparse mode (PIM-SM).
By default, the RP is needed only to start new sessions with sources and receivers.
Reference:
https://www.cisco.com/c/en/us/td/docs/ios/solutions_docs/ip_multicast/White_papers/rps.html
For your information, in PIM-SM, only network segments with active receivers that have explicitly requested multicast data will be forwarded the traffic. This method of delivering multicast data is in contrast to the PIM dense mode (PIM-DM) model. In PIM-DM, multicast traffic is initially flooded to all segments of the network. Routers that have no downstream neighbors or directly connected receivers prune back the unwanted traffic.
CiscoのOracle 1z0-915-1試験トレーニングソースを提供するサイトがたくさんありますが、Omgzlookは最実用な資料を提供します。 SAP C-S4CPR-2408 - もし学習教材は問題があれば、或いは試験に不合格になる場合は、全額返金することを保証いたします。 OmgzlookのCiscoのIBM C1000-172試験トレーニング資料を手に入れたら、我々は一年間の無料更新サービスを提供します。 Omgzlookの CiscoのCompTIA 220-1101J試験トレーニング資料を手に入れるなら、君が他の人の一半の努力で、同じCiscoのCompTIA 220-1101J認定試験を簡単に合格できます。 Cisco 200-301J - Omgzlookを選んだら、成功への扉を開きます。
Updated: May 28, 2022