それは正確性が高くて、カバー率も広いです。あなたはOmgzlookの学習教材を購入した後、私たちは一年間で無料更新サービスを提供することができます。OmgzlookのCiscoの350-401試験資料試験トレーニング資料はCiscoの350-401試験資料認定試験を準備するのリーダーです。 OmgzlookはCiscoの350-401試験資料の認定試験を真実に、全面的に研究したサイトです。Omgzlook のユニークなCiscoの350-401試験資料の認定試験の問題と解答を利用したら、試験に合格することがたやすくなります。 もちろん、我々はあなたに一番安心させるのは我々の開発する多くの受験生に合格させるCiscoの350-401試験資料試験のソフトウェアです。
CCNP Enterprise 350-401 それはあなたが夢を実現することを助けられます。
我々の開発するCiscoの350-401 - Implementing Cisco Enterprise Network Core Technologies (350-401 ENCOR)試験資料ソフトは最新で最も豊富な問題集を含めています。 さて、はやく試験を申し込みましょう。Omgzlookはあなたを助けることができますから、心配する必要がないですよ。
我々OmgzlookのITエリートと我々のCiscoの350-401試験資料試験のソフトに満足するお客様は我々に自信を持たせます。あなたのCiscoの350-401試験資料試験を準備する圧力を減少するのは我々の責任で、あなたにCiscoの350-401試験資料試験に合格させるのは我々の目標です。我々はほぼ100％の通過率であなたに安心させます。
Cisco 350-401試験資料 - Omgzlookから大変助かりました。
OmgzlookのCiscoの350-401試験資料試験トレーニング資料は豊富な経験を持っているIT専門家が研究したものです。君がCiscoの350-401試験資料問題集を購入したら、私たちは一年間で無料更新サービスを提供することができます。もしCiscoの350-401試験資料問題集は問題があれば、或いは試験に不合格になる場合は、全額返金することを保証いたします。
70％の問題は解説がありますし、試験の内容を理解しやすいと助けます。常にCisco 350-401試験資料試験に参加する予定があるお客様は「こちらの問題集には、全部で何問位、掲載されておりますか？」といった質問を提出しました。
350-401 PDF DEMO:
QUESTION NO: 1
What is the difference between a RIB and a FIB?
A. The FIB is populated based on RIB content
B. The RIB is used to make IP source prefix-based switching decisions
C. The RIB maintains a mirror image of the FIB
D. The FIB is where all IP routing information is stored
Answer: A
Explanation:
CEF uses a Forwarding Information Base (FIB) to make IP destination prefix-based switching decisions.
The FIB is conceptually similar to a routing table or information base. It maintains a mirror image of the forwarding information contained in the IP routing table. When routing or topology changes occur in the network, the IP routing table is updated, and those changes are reflected in the FIB. The
FIB maintains next-hop address information based on the information in the IP routing table. Because there is a one-to-one correlation between FIB entries and routing table entries, the FIB contains all known routes and eliminates the need for route cache maintenance that is associated with earlier switching paths such as fast switching and optimum switching.
Note: In order to view the Routing information base (RIB) table, use the "show ip route" command.
To view the Forwarding Information Base (FIB), use the "show ip cef" command. RIB is in Control plane while FIB is in Data plane.
QUESTION NO: 2
Which feature does Cisco TrustSec use to provide scalable, secure communication throughout a network?
A. security group tag number assigned to each user on a switch
B. security group tag ACL assigned to each router on a network
C. security group tag ACL assigned to each port on a switch
D. security group tag number assigned to each port on a network
Answer: D
Explanation:
Cisco TrustSec uses tags to represent logical group privilege. This tag, called a Security Group Tag
(SGT), is used in access policies. The SGT is understood and is used to enforce traffic by Cisco switches, routers and firewalls . Cisco TrustSec is defined in three phases: classification, propagation and enforcement.
When users and devices connect to a network, the network assigns a specific security group.
This process is called classification. Classification can be based on the results of the authentication or by associating the SGT with an IP, VLAN, or port-profile (-> Answer A and answer C are not correct as they say "assigned ... on a switch" only. Answer D is not correct either as it says "assigned to each router").
QUESTION NO: 3
To increase total throughput and redundancy on the links between the wireless controller and switch, the customer enabled LAG on the wireless controller.
Which EtherChannel mode must be configured on the switch to allow the WLC to connect?
A. Active
B. On
C. Auto
D. Passive
Answer: B
Explanation:
Restrictions for Link Aggregation:
You can bundle all eight ports on a Cisco 5508 Controller into a single link.
Terminating on two different modules within a single Catalyst 6500 series switch provides redundancy and ensures that connectivity between the switch and the controller is maintained when one module fails. The controller's port 1 is connected to Gigabit interface 3/1, and the controller's port 2 is connected to Gigabit interface 2/1 on the Catalyst 6500 series switch. Both switch ports are assigned to the same channel group.
LAG requires the EtherChannel to be configured for 'mode on' on both the controller and the Catalyst switch.
Once the EtherChannel is configured as on at both ends of the link, the Catalyst switch should not be configured for either Link Aggregation Control Protocol (LACP) or Cisco proprietary Port Aggregation
Protocol (PAgP) but be set unconditionally to LAG. Because no channel negotiation is done between the controller and the switch, the controller does not answer to negotiation frames and the LAG is not formed if a dynamic form of LAG is set on the switch. Additionally, LACP and PAgP are not supported on the controller.
If the recommended load-balancing method cannot be configured on the Catalyst switch, then configure the LAG connection as a single member link or disable LAG on the controller.
https://www.cisco.com/c/en/us/td/docs/wireless/controller/7-5/configuration- guide/b_cg75/b_cg75_chapter_0100010.html
QUESTION NO: 4
Which technology provides a secure communication channel for all traffic at Layer 2 of the OSI model?
A. IPsec
B. Cisco Trustsec
C. MACsec
D. SSL
Answer: C
Explanation:
MACsec, defined in 802.1AE, provides MAC-layer encryption over wired networks by using out- of
-band methods for encryption keying. The MACsec Key Agreement (MKA) Protocol provides the required session keys and manages the required encryption keys. MKA and MACsec are implemented after successful authentication using the 802.1x Extensible Authentication Protocol (EAP-TLS) or Pre
Shared Key (PSK) framework.
A switch using MACsec accepts either MACsec or non-MACsec frames, depending on the policy associated with the MKA peer. MACsec frames are encrypted and protected with an integrity check value (ICV). When the switch receives frames from the MKA peer, it decrypts them and calculates the correct ICV by using session keys provided by MKA. The switch compares that ICV to the ICV within the frame. If they are not identical, the frame is dropped. The switch also encrypts and adds an ICV to any frames sent over the secured port (the access point used to provide the secure MAC service to a
MKA peer) using the current session key.
Reference: https://www.cisco.com/c/en/us/td/docs/switches/lan/catalyst9300/software/release/16-
9/configuration_guide/sec/b_169_sec_9300_cg/macsec_encryption.html
Note: Cisco Trustsec is the solution which includes MACsec.
QUESTION NO: 5
Refer to the exhibit. A port channel is configured between SW2 and SW3. SW2 is not running a
Cisco operating system. When all physical connections are mode, the port channel does not establish.
Based on the configuration excerpt of SW3, what is the cause of the problem?
A. The port-channel interface lead balance should be set to src-mac
B. The port-channel trunk is not allowing the native VLAN.
C. The port-channel should be set to auto.
D. The port channel on SW2 is using an incompatible protocol.
Answer: D
Explanation:
The Cisco switch was configured with PAgP, which is a Cisco proprietary protocol so non-Cisco switch could not communicate.
弊社のソフトを使用して、ほとんどのお客様は難しいと思われているCiscoのIBM C1000-176試験に順調に剛角しました。 Microsoft AZ-900-JPN - あらゆる人にとって、時間は非常に大切です。 Salesforce CRM-Analytics-and-Einstein-Discovery-Consultant - これをよくできるために、我々は全日24時間のサービスを提供します。 でも、Cisco Microsoft PL-300-KR復習教材を選ばれば、試験に合格することは簡単です。 暇な時間だけでCiscoのVMware 2V0-12.24試験に合格したいのですか。
Updated: May 28, 2022