それを利用したら、君のCiscoの350-401試験対応認定試験に合格するのは問題ありません。もしOmgzlookの学習教材を購入した後、どんな問題があれば、或いは試験に不合格になる場合は、私たちが全額返金することを保証いたします。Omgzlookを信じて、私たちは君のそばにいるから。 購入した前の無料の試み、購入するときのお支払いへの保障、購入した一年間の無料更新Ciscoの350-401試験対応試験に失敗した全額での返金…これらは我々のお客様への承諾です。常々、時間とお金ばかり効果がないです。 あなたが試験に合格するのは我々への一番よい評価です。
早く350-401試験対応試験参考書を買いましょう！
Omgzlookの専門家チームがCiscoの350-401 - Implementing Cisco Enterprise Network Core Technologies (350-401 ENCOR)試験対応認証試験に対して最新の短期有効なトレーニングプログラムを研究しました。 君の明るい将来を祈っています。みなさんにOmgzlookを選ぶのはより安心させるためにOmgzlookは部分のCisco 350-401 試験解説「Implementing Cisco Enterprise Network Core Technologies (350-401 ENCOR)」試験材料がネットで提供して、君が無料でダウンロードすることができます。
OmgzlookのCiscoの350-401試験対応認証試験について最新な研究を完成いたしました。無料な部分ダウンロードしてください。きっと君に失望させないと信じています。
Cisco 350-401試験対応 - あなたが試験に合格することを助けられますから。
我々はあなたに提供するのは最新で一番全面的なCiscoの350-401試験対応問題集で、最も安全な購入保障で、最もタイムリーなCiscoの350-401試験対応試験のソフトウェアの更新です。無料デモはあなたに安心で購入して、購入した後1年間の無料Ciscoの350-401試験対応試験の更新はあなたに安心で試験を準備することができます、あなたは確実に購入を休ませることができます私たちのソフトウェアを試してみてください。もちろん、我々はあなたに一番安心させるのは我々の開発する多くの受験生に合格させるCiscoの350-401試験対応試験のソフトウェアです。
それに、一年間の無料更新サービスを提供することができます。Omgzlook はプロなウェブサイトで、受験生の皆さんに質の高いサービスを提供します。
350-401 PDF DEMO:
QUESTION NO: 1
To increase total throughput and redundancy on the links between the wireless controller and switch, the customer enabled LAG on the wireless controller.
Which EtherChannel mode must be configured on the switch to allow the WLC to connect?
A. Active
B. On
C. Auto
D. Passive
Answer: B
Explanation:
Restrictions for Link Aggregation:
You can bundle all eight ports on a Cisco 5508 Controller into a single link.
Terminating on two different modules within a single Catalyst 6500 series switch provides redundancy and ensures that connectivity between the switch and the controller is maintained when one module fails. The controller's port 1 is connected to Gigabit interface 3/1, and the controller's port 2 is connected to Gigabit interface 2/1 on the Catalyst 6500 series switch. Both switch ports are assigned to the same channel group.
LAG requires the EtherChannel to be configured for 'mode on' on both the controller and the Catalyst switch.
Once the EtherChannel is configured as on at both ends of the link, the Catalyst switch should not be configured for either Link Aggregation Control Protocol (LACP) or Cisco proprietary Port Aggregation
Protocol (PAgP) but be set unconditionally to LAG. Because no channel negotiation is done between the controller and the switch, the controller does not answer to negotiation frames and the LAG is not formed if a dynamic form of LAG is set on the switch. Additionally, LACP and PAgP are not supported on the controller.
If the recommended load-balancing method cannot be configured on the Catalyst switch, then configure the LAG connection as a single member link or disable LAG on the controller.
https://www.cisco.com/c/en/us/td/docs/wireless/controller/7-5/configuration- guide/b_cg75/b_cg75_chapter_0100010.html
QUESTION NO: 2
Which technology provides a secure communication channel for all traffic at Layer 2 of the OSI model?
A. IPsec
B. Cisco Trustsec
C. MACsec
D. SSL
Answer: C
Explanation:
MACsec, defined in 802.1AE, provides MAC-layer encryption over wired networks by using out- of
-band methods for encryption keying. The MACsec Key Agreement (MKA) Protocol provides the required session keys and manages the required encryption keys. MKA and MACsec are implemented after successful authentication using the 802.1x Extensible Authentication Protocol (EAP-TLS) or Pre
Shared Key (PSK) framework.
A switch using MACsec accepts either MACsec or non-MACsec frames, depending on the policy associated with the MKA peer. MACsec frames are encrypted and protected with an integrity check value (ICV). When the switch receives frames from the MKA peer, it decrypts them and calculates the correct ICV by using session keys provided by MKA. The switch compares that ICV to the ICV within the frame. If they are not identical, the frame is dropped. The switch also encrypts and adds an ICV to any frames sent over the secured port (the access point used to provide the secure MAC service to a
MKA peer) using the current session key.
Reference: https://www.cisco.com/c/en/us/td/docs/switches/lan/catalyst9300/software/release/16-
9/configuration_guide/sec/b_169_sec_9300_cg/macsec_encryption.html
Note: Cisco Trustsec is the solution which includes MACsec.
QUESTION NO: 3
What is the difference between a RIB and a FIB?
A. The FIB is populated based on RIB content
B. The RIB is used to make IP source prefix-based switching decisions
C. The RIB maintains a mirror image of the FIB
D. The FIB is where all IP routing information is stored
Answer: A
Explanation:
CEF uses a Forwarding Information Base (FIB) to make IP destination prefix-based switching decisions.
The FIB is conceptually similar to a routing table or information base. It maintains a mirror image of the forwarding information contained in the IP routing table. When routing or topology changes occur in the network, the IP routing table is updated, and those changes are reflected in the FIB. The
FIB maintains next-hop address information based on the information in the IP routing table. Because there is a one-to-one correlation between FIB entries and routing table entries, the FIB contains all known routes and eliminates the need for route cache maintenance that is associated with earlier switching paths such as fast switching and optimum switching.
Note: In order to view the Routing information base (RIB) table, use the "show ip route" command.
To view the Forwarding Information Base (FIB), use the "show ip cef" command. RIB is in Control plane while FIB is in Data plane.
QUESTION NO: 4
Refer to the exhibit. A port channel is configured between SW2 and SW3. SW2 is not running a
Cisco operating system. When all physical connections are mode, the port channel does not establish.
Based on the configuration excerpt of SW3, what is the cause of the problem?
A. The port-channel interface lead balance should be set to src-mac
B. The port-channel trunk is not allowing the native VLAN.
C. The port-channel should be set to auto.
D. The port channel on SW2 is using an incompatible protocol.
Answer: D
Explanation:
The Cisco switch was configured with PAgP, which is a Cisco proprietary protocol so non-Cisco switch could not communicate.
QUESTION NO: 5
Which statement about multicast RPs is true?
A. RPs are required for protocol independent multicast sparse mode and dense mode.
B. By default, the RP is needed only to start new sessions with sources and receivers.
C. By default, the RP is needed periodically to maintain sessions with sources and receivers
D. RPs are required only when using protocol independent multicast dense mode.
Answer: B
Explanation:
A rendezvous point (RP) is required only in networks running Protocol Independent Multicast sparse mode (PIM-SM).
By default, the RP is needed only to start new sessions with sources and receivers.
Reference:
https://www.cisco.com/c/en/us/td/docs/ios/solutions_docs/ip_multicast/White_papers/rps.html
For your information, in PIM-SM, only network segments with active receivers that have explicitly requested multicast data will be forwarded the traffic. This method of delivering multicast data is in contrast to the PIM dense mode (PIM-DM) model. In PIM-DM, multicast traffic is initially flooded to all segments of the network. Routers that have no downstream neighbors or directly connected receivers prune back the unwanted traffic.
Cisco 200-301 - 我々の承諾だけでなく、お客様に最も全面的で最高のサービスを提供します。 IBM S2000-024 - 試験がたいへん難しいですから悩んでいるのですか。 自分の能力を証明するために、Amazon CLF-C02試験に合格するのは不可欠なことです。 IBM C1000-127 - あなたに最大の利便性を与えるために、Omgzlookは様々なバージョンの教材を用意しておきます。 PECB Lead-Cybersecurity-Manager - 我々Omgzlookは一番行き届いたアフタサービスを提供します。
Updated: May 28, 2022