君はまずネットで無料なCiscoの350-401最新受験攻略試験問題をダウンロードしてから 弊社の品質を確信してから、購入してください。Omgzlookは提供した商品は君の成功を全力で助けさしたげます。 それはあなたが夢を実現することを助けられます。夢を持ったら実現するために頑張ってください。 しかし必ずしも大量の時間とエネルギーで復習しなくて、弊社が丹精にできあがった問題集を使って、試験なんて問題ではありません。
CCNP Enterprise 350-401 あなたの夢は何ですか。
CCNP Enterprise 350-401最新受験攻略 - Implementing Cisco Enterprise Network Core Technologies (350-401 ENCOR) Omgzlookが持つべきなIT問題集を提供するサイトでございます。 Omgzlookの350-401 合格問題教材を購入したら、あなたは一年間の無料アップデートサービスを取得しました。試験問題集が更新されると、Omgzlookは直ちにあなたのメールボックスに350-401 合格問題問題集の最新版を送ります。
IT業の多くの人がいくつか認証試験にパスしたくて、それなりの合格証明書が君に最大な上昇空間を与えます。この競争の激しい業界でとんとん拍子に出世させるのはCiscoの350-401最新受験攻略認定試験ですが、簡単にパスではありません。でもたくさんの方法があって、最も少ない時間をエネルギーをかかるのは最高です。
Cisco 350-401最新受験攻略 - 我々もオンライン版とソフト版を提供します。
OmgzlookのCiscoの350-401最新受験攻略試験トレーニング資料の知名度が非常に高いことを皆はよく知っています。Omgzlook は世界的によく知られているサイトです。どうしてこのような大きな連鎖反応になりましたか。それはOmgzlookのCiscoの350-401最新受験攻略試験トレーニング資料は適用性が高いもので、本当にみなさんが良い成績を取ることを助けられるからです。
我々OmgzlookはCiscoの350-401最新受験攻略試験問題集をリリースする以降、多くのお客様の好評を博したのは弊社にとって、大変な名誉なことです。また、我々はさらに認可を受けられるために、皆様の一切の要求を満足できて喜ぶ気持ちでずっと協力し、完備かつ精確の350-401最新受験攻略試験問題集を開発するのに準備します。
350-401 PDF DEMO:
QUESTION NO: 1
What is the difference between a RIB and a FIB?
A. The FIB is populated based on RIB content
B. The RIB is used to make IP source prefix-based switching decisions
C. The RIB maintains a mirror image of the FIB
D. The FIB is where all IP routing information is stored
Answer: A
Explanation:
CEF uses a Forwarding Information Base (FIB) to make IP destination prefix-based switching decisions.
The FIB is conceptually similar to a routing table or information base. It maintains a mirror image of the forwarding information contained in the IP routing table. When routing or topology changes occur in the network, the IP routing table is updated, and those changes are reflected in the FIB. The
FIB maintains next-hop address information based on the information in the IP routing table. Because there is a one-to-one correlation between FIB entries and routing table entries, the FIB contains all known routes and eliminates the need for route cache maintenance that is associated with earlier switching paths such as fast switching and optimum switching.
Note: In order to view the Routing information base (RIB) table, use the "show ip route" command.
To view the Forwarding Information Base (FIB), use the "show ip cef" command. RIB is in Control plane while FIB is in Data plane.
QUESTION NO: 2
Which feature does Cisco TrustSec use to provide scalable, secure communication throughout a network?
A. security group tag number assigned to each user on a switch
B. security group tag ACL assigned to each router on a network
C. security group tag ACL assigned to each port on a switch
D. security group tag number assigned to each port on a network
Answer: D
Explanation:
Cisco TrustSec uses tags to represent logical group privilege. This tag, called a Security Group Tag
(SGT), is used in access policies. The SGT is understood and is used to enforce traffic by Cisco switches, routers and firewalls . Cisco TrustSec is defined in three phases: classification, propagation and enforcement.
When users and devices connect to a network, the network assigns a specific security group.
This process is called classification. Classification can be based on the results of the authentication or by associating the SGT with an IP, VLAN, or port-profile (-> Answer A and answer C are not correct as they say "assigned ... on a switch" only. Answer D is not correct either as it says "assigned to each router").
QUESTION NO: 3
To increase total throughput and redundancy on the links between the wireless controller and switch, the customer enabled LAG on the wireless controller.
Which EtherChannel mode must be configured on the switch to allow the WLC to connect?
A. Active
B. On
C. Auto
D. Passive
Answer: B
Explanation:
Restrictions for Link Aggregation:
You can bundle all eight ports on a Cisco 5508 Controller into a single link.
Terminating on two different modules within a single Catalyst 6500 series switch provides redundancy and ensures that connectivity between the switch and the controller is maintained when one module fails. The controller's port 1 is connected to Gigabit interface 3/1, and the controller's port 2 is connected to Gigabit interface 2/1 on the Catalyst 6500 series switch. Both switch ports are assigned to the same channel group.
LAG requires the EtherChannel to be configured for 'mode on' on both the controller and the Catalyst switch.
Once the EtherChannel is configured as on at both ends of the link, the Catalyst switch should not be configured for either Link Aggregation Control Protocol (LACP) or Cisco proprietary Port Aggregation
Protocol (PAgP) but be set unconditionally to LAG. Because no channel negotiation is done between the controller and the switch, the controller does not answer to negotiation frames and the LAG is not formed if a dynamic form of LAG is set on the switch. Additionally, LACP and PAgP are not supported on the controller.
If the recommended load-balancing method cannot be configured on the Catalyst switch, then configure the LAG connection as a single member link or disable LAG on the controller.
https://www.cisco.com/c/en/us/td/docs/wireless/controller/7-5/configuration- guide/b_cg75/b_cg75_chapter_0100010.html
QUESTION NO: 4
Which technology provides a secure communication channel for all traffic at Layer 2 of the OSI model?
A. IPsec
B. Cisco Trustsec
C. MACsec
D. SSL
Answer: C
Explanation:
MACsec, defined in 802.1AE, provides MAC-layer encryption over wired networks by using out- of
-band methods for encryption keying. The MACsec Key Agreement (MKA) Protocol provides the required session keys and manages the required encryption keys. MKA and MACsec are implemented after successful authentication using the 802.1x Extensible Authentication Protocol (EAP-TLS) or Pre
Shared Key (PSK) framework.
A switch using MACsec accepts either MACsec or non-MACsec frames, depending on the policy associated with the MKA peer. MACsec frames are encrypted and protected with an integrity check value (ICV). When the switch receives frames from the MKA peer, it decrypts them and calculates the correct ICV by using session keys provided by MKA. The switch compares that ICV to the ICV within the frame. If they are not identical, the frame is dropped. The switch also encrypts and adds an ICV to any frames sent over the secured port (the access point used to provide the secure MAC service to a
MKA peer) using the current session key.
Reference: https://www.cisco.com/c/en/us/td/docs/switches/lan/catalyst9300/software/release/16-
9/configuration_guide/sec/b_169_sec_9300_cg/macsec_encryption.html
Note: Cisco Trustsec is the solution which includes MACsec.
QUESTION NO: 5
Refer to the exhibit. A port channel is configured between SW2 and SW3. SW2 is not running a
Cisco operating system. When all physical connections are mode, the port channel does not establish.
Based on the configuration excerpt of SW3, what is the cause of the problem?
A. The port-channel interface lead balance should be set to src-mac
B. The port-channel trunk is not allowing the native VLAN.
C. The port-channel should be set to auto.
D. The port channel on SW2 is using an incompatible protocol.
Answer: D
Explanation:
The Cisco switch was configured with PAgP, which is a Cisco proprietary protocol so non-Cisco switch could not communicate.
Scrum SAFe-SASM - Omgzlookを選んだら成功を選んだということです。 ほんとんどお客様は我々OmgzlookのCisco Microsoft MB-230J問題集を使用してから試験にうまく合格しましたのは弊社の試験資料の有効性と信頼性を説明できます。 Microsoft MB-230 - それはOmgzlookは長年の経験を持っていて、ずっとIT認定試験の研究に取り組んでいて、試験についての多くの規則を総括しましたから。 Fortinet NSE7_SDW-7.2問題集のカーバー率が高いので、勉強した問題は試験に出ることが多いです。 Juniper JN0-252 - 二つのバージョンのどちらでもダウンロードできますから、Omgzlookのサイトで検索してダウンロードすることができます。
Updated: May 28, 2022