OmgzlookのCiscoの350-401日本語的中対策試験トレーニング資料は最高のトレーニング資料です。IT職員としてのあなたは切迫感を感じましたか。Omgzlookを選んだら、成功への扉を開きます。 350-401日本語的中対策問題集のカーバー率が高いので、勉強した問題は試験に出ることが多いです。だから、弊社の提供する350-401日本語的中対策問題集を暗記すれば、きっと試験に合格できます。 IT技術の急速な発展につれて、IT認証試験の問題は常に変更されています。
CCNP Enterprise 350-401 できるだけ100％の通過率を保証使用にしています。
350-401 - Implementing Cisco Enterprise Network Core Technologies (350-401 ENCOR)日本語的中対策はCiscoの一つ重要な認証試験で多くのIT専門スタッフが認証される重要な試験です。 ただ、社会に入るIT卒業生たちは自分能力の不足で、350-401 的中合格問題集試験向けの仕事を探すのを悩んでいますか？それでは、弊社のCiscoの350-401 的中合格問題集練習問題を選んで実用能力を速く高め、自分を充実させます。その結果、自信になる自己は面接のときに、面接官のいろいろな質問を気軽に回答できて、順調に350-401 的中合格問題集向けの会社に入ります。
ですから、弊社のトレーニング製品はあなたが試験に合格することを助けにならなかったら、全額で返金することを保証します。Ciscoの350-401日本語的中対策のオンラインサービスのスタディガイドを買いたかったら、Omgzlookを買うのを薦めています。Omgzlookは同じ作用がある多くのサイトでリーダーとしているサイトで、最も良い品質と最新のトレーニング資料を提供しています。
Cisco 350-401日本語的中対策 - この試験に受かるのは難しいですが、大丈夫です。
Ciscoの350-401日本語的中対策の認定試験に合格すれば、就職機会が多くなります。この試験に合格すれば君の専門知識がとても強いを証明し得ます。Ciscoの350-401日本語的中対策の認定試験は君の実力を考察するテストでございます。
Omgzlookは優れたIT情報のソースを提供するサイトです。Omgzlookで、あなたの試験のためのテクニックと勉強資料を見つけることができます。
350-401 PDF DEMO:
QUESTION NO: 1
Which statement about multicast RPs is true?
A. RPs are required for protocol independent multicast sparse mode and dense mode.
B. By default, the RP is needed only to start new sessions with sources and receivers.
C. By default, the RP is needed periodically to maintain sessions with sources and receivers
D. RPs are required only when using protocol independent multicast dense mode.
Answer: B
Explanation:
A rendezvous point (RP) is required only in networks running Protocol Independent Multicast sparse mode (PIM-SM).
By default, the RP is needed only to start new sessions with sources and receivers.
Reference:
https://www.cisco.com/c/en/us/td/docs/ios/solutions_docs/ip_multicast/White_papers/rps.html
For your information, in PIM-SM, only network segments with active receivers that have explicitly requested multicast data will be forwarded the traffic. This method of delivering multicast data is in contrast to the PIM dense mode (PIM-DM) model. In PIM-DM, multicast traffic is initially flooded to all segments of the network. Routers that have no downstream neighbors or directly connected receivers prune back the unwanted traffic.
QUESTION NO: 2
Refer to the exhibit. A port channel is configured between SW2 and SW3. SW2 is not running a
Cisco operating system. When all physical connections are mode, the port channel does not establish.
Based on the configuration excerpt of SW3, what is the cause of the problem?
A. The port-channel interface lead balance should be set to src-mac
B. The port-channel trunk is not allowing the native VLAN.
C. The port-channel should be set to auto.
D. The port channel on SW2 is using an incompatible protocol.
Answer: D
Explanation:
The Cisco switch was configured with PAgP, which is a Cisco proprietary protocol so non-Cisco switch could not communicate.
QUESTION NO: 3
Which access controls list allows only TCP traffic with a destination port range of 22-433, excluding port 80?
A. Deny tcp any any ne 80
Permit tcp any any range 22 443
B. Permit tcp any any ne 80
C. Permit tco any any range 22 443
Deny tcp any any eq 80
D. Deny tcp any any eq 80
Permit tco any any gt 21 it 444
Answer: D
QUESTION NO: 4
Which technology provides a secure communication channel for all traffic at Layer 2 of the OSI model?
A. IPsec
B. Cisco Trustsec
C. MACsec
D. SSL
Answer: C
Explanation:
MACsec, defined in 802.1AE, provides MAC-layer encryption over wired networks by using out- of
-band methods for encryption keying. The MACsec Key Agreement (MKA) Protocol provides the required session keys and manages the required encryption keys. MKA and MACsec are implemented after successful authentication using the 802.1x Extensible Authentication Protocol (EAP-TLS) or Pre
Shared Key (PSK) framework.
A switch using MACsec accepts either MACsec or non-MACsec frames, depending on the policy associated with the MKA peer. MACsec frames are encrypted and protected with an integrity check value (ICV). When the switch receives frames from the MKA peer, it decrypts them and calculates the correct ICV by using session keys provided by MKA. The switch compares that ICV to the ICV within the frame. If they are not identical, the frame is dropped. The switch also encrypts and adds an ICV to any frames sent over the secured port (the access point used to provide the secure MAC service to a
MKA peer) using the current session key.
Reference: https://www.cisco.com/c/en/us/td/docs/switches/lan/catalyst9300/software/release/16-
9/configuration_guide/sec/b_169_sec_9300_cg/macsec_encryption.html
Note: Cisco Trustsec is the solution which includes MACsec.
QUESTION NO: 5
To increase total throughput and redundancy on the links between the wireless controller and switch, the customer enabled LAG on the wireless controller.
Which EtherChannel mode must be configured on the switch to allow the WLC to connect?
A. Active
B. On
C. Auto
D. Passive
Answer: B
Explanation:
Restrictions for Link Aggregation:
You can bundle all eight ports on a Cisco 5508 Controller into a single link.
Terminating on two different modules within a single Catalyst 6500 series switch provides redundancy and ensures that connectivity between the switch and the controller is maintained when one module fails. The controller's port 1 is connected to Gigabit interface 3/1, and the controller's port 2 is connected to Gigabit interface 2/1 on the Catalyst 6500 series switch. Both switch ports are assigned to the same channel group.
LAG requires the EtherChannel to be configured for 'mode on' on both the controller and the Catalyst switch.
Once the EtherChannel is configured as on at both ends of the link, the Catalyst switch should not be configured for either Link Aggregation Control Protocol (LACP) or Cisco proprietary Port Aggregation
Protocol (PAgP) but be set unconditionally to LAG. Because no channel negotiation is done between the controller and the switch, the controller does not answer to negotiation frames and the LAG is not formed if a dynamic form of LAG is set on the switch. Additionally, LACP and PAgP are not supported on the controller.
If the recommended load-balancing method cannot be configured on the Catalyst switch, then configure the LAG connection as a single member link or disable LAG on the controller.
https://www.cisco.com/c/en/us/td/docs/wireless/controller/7-5/configuration- guide/b_cg75/b_cg75_chapter_0100010.html
IBM C1000-005 - あなたの全部な需要を満たすためにいつも頑張ります。 Esri EJSA_2024 - しかしながら、試験の大切さと同じ、この試験も非常に難しいです。 Omgzlookの専門家チームがCiscoのFortinet NSE6_WCS-7.0認証試験に対して最新の短期有効なトレーニングプログラムを研究しました。 OmgzlookのHitachi HQT-4420問題集はあなたに合う最善の勉強法です。 OmgzlookのCiscoのMicrosoft AZ-400認証試験について最新な研究を完成いたしました。
Updated: May 28, 2022