こうして、君は安心で試験の準備を行ってください。弊社の資料を使って、１００％に合格を保証いたします。もし合格しないと、われは全額で返金いたします。 あなたはいつでもサブスクリプションの期間を延長することができますから、より多くの時間を取って充分に試験を準備できます。Omgzlookというサイトのトレーニング資料を利用するかどうかがまだ決まっていなかったら、Omgzlookのウェブで一部の試験問題と解答を無料にダウンローしてみることができます。 そしてあなたに350-401日本語的中対策試験に関するテスト問題と解答が分析して差し上げるうちにあなたのIT専門知識を固めています。
CCNP Enterprise 350-401 近年、IT領域で競争がますます激しくなります。
IT専門知識をテストしているCiscoの350-401 - Implementing Cisco Enterprise Network Core Technologies (350-401 ENCOR)日本語的中対策認定試験は1つのとても重要な認証試験でございます。 OmgzlookのCiscoの350-401 最新な問題集試験トレーニング資料は豊富な知識と経験を持っているIT専門家に研究された成果で、正確度がとても高いです。Omgzlookに会ったら、最高のトレーニング資料を見つけました。
Omgzlookが開発された試験の問題と解答は異なるターゲットに含まれていますし、カバー率が高いですから、それを超える書籍や資料が絶対ありません。大勢の人たちの利用結果によると、Omgzlookの合格率は１００パーセントに達したのですから、絶対あなたが試験を受かることに重要な助けになれます。Omgzlookは唯一のあなたの向いている試験に合格する方法で、Omgzlookを選んだら、美しい未来を選んだということになります。
Cisco 350-401日本語的中対策 - では、どうやって自分の能力を証明するのですか。
世の中に去年の自分より今年の自分が優れていないのは立派な恥です。それで、IT人材として毎日自分を充実して、350-401日本語的中対策問題集を学ぶ必要があります。弊社の350-401日本語的中対策問題集はあなたにこのチャンスを全面的に与えられます。あなたは自分の望ましいCisco 350-401日本語的中対策問題集を選らんで、学びから更なる成長を求められます。心はもはや空しくなく、生活を美しくなります。
最新の350-401日本語的中対策試験問題を知りたい場合、試験に合格したとしてもOmgzlookは無料で問題集を更新してあげます。Omgzlookの350-401日本語的中対策教材を購入したら、あなたは一年間の無料アップデートサービスを取得しました。
350-401 PDF DEMO:
QUESTION NO: 1
What is the difference between a RIB and a FIB?
A. The FIB is populated based on RIB content
B. The RIB is used to make IP source prefix-based switching decisions
C. The RIB maintains a mirror image of the FIB
D. The FIB is where all IP routing information is stored
Answer: A
Explanation:
CEF uses a Forwarding Information Base (FIB) to make IP destination prefix-based switching decisions.
The FIB is conceptually similar to a routing table or information base. It maintains a mirror image of the forwarding information contained in the IP routing table. When routing or topology changes occur in the network, the IP routing table is updated, and those changes are reflected in the FIB. The
FIB maintains next-hop address information based on the information in the IP routing table. Because there is a one-to-one correlation between FIB entries and routing table entries, the FIB contains all known routes and eliminates the need for route cache maintenance that is associated with earlier switching paths such as fast switching and optimum switching.
Note: In order to view the Routing information base (RIB) table, use the "show ip route" command.
To view the Forwarding Information Base (FIB), use the "show ip cef" command. RIB is in Control plane while FIB is in Data plane.
QUESTION NO: 2
To increase total throughput and redundancy on the links between the wireless controller and switch, the customer enabled LAG on the wireless controller.
Which EtherChannel mode must be configured on the switch to allow the WLC to connect?
A. Active
B. On
C. Auto
D. Passive
Answer: B
Explanation:
Restrictions for Link Aggregation:
You can bundle all eight ports on a Cisco 5508 Controller into a single link.
Terminating on two different modules within a single Catalyst 6500 series switch provides redundancy and ensures that connectivity between the switch and the controller is maintained when one module fails. The controller's port 1 is connected to Gigabit interface 3/1, and the controller's port 2 is connected to Gigabit interface 2/1 on the Catalyst 6500 series switch. Both switch ports are assigned to the same channel group.
LAG requires the EtherChannel to be configured for 'mode on' on both the controller and the Catalyst switch.
Once the EtherChannel is configured as on at both ends of the link, the Catalyst switch should not be configured for either Link Aggregation Control Protocol (LACP) or Cisco proprietary Port Aggregation
Protocol (PAgP) but be set unconditionally to LAG. Because no channel negotiation is done between the controller and the switch, the controller does not answer to negotiation frames and the LAG is not formed if a dynamic form of LAG is set on the switch. Additionally, LACP and PAgP are not supported on the controller.
If the recommended load-balancing method cannot be configured on the Catalyst switch, then configure the LAG connection as a single member link or disable LAG on the controller.
https://www.cisco.com/c/en/us/td/docs/wireless/controller/7-5/configuration- guide/b_cg75/b_cg75_chapter_0100010.html
QUESTION NO: 3
Which technology provides a secure communication channel for all traffic at Layer 2 of the OSI model?
A. IPsec
B. Cisco Trustsec
C. MACsec
D. SSL
Answer: C
Explanation:
MACsec, defined in 802.1AE, provides MAC-layer encryption over wired networks by using out- of
-band methods for encryption keying. The MACsec Key Agreement (MKA) Protocol provides the required session keys and manages the required encryption keys. MKA and MACsec are implemented after successful authentication using the 802.1x Extensible Authentication Protocol (EAP-TLS) or Pre
Shared Key (PSK) framework.
A switch using MACsec accepts either MACsec or non-MACsec frames, depending on the policy associated with the MKA peer. MACsec frames are encrypted and protected with an integrity check value (ICV). When the switch receives frames from the MKA peer, it decrypts them and calculates the correct ICV by using session keys provided by MKA. The switch compares that ICV to the ICV within the frame. If they are not identical, the frame is dropped. The switch also encrypts and adds an ICV to any frames sent over the secured port (the access point used to provide the secure MAC service to a
MKA peer) using the current session key.
Reference: https://www.cisco.com/c/en/us/td/docs/switches/lan/catalyst9300/software/release/16-
9/configuration_guide/sec/b_169_sec_9300_cg/macsec_encryption.html
Note: Cisco Trustsec is the solution which includes MACsec.
QUESTION NO: 4
Which feature does Cisco TrustSec use to provide scalable, secure communication throughout a network?
A. security group tag number assigned to each user on a switch
B. security group tag ACL assigned to each router on a network
C. security group tag ACL assigned to each port on a switch
D. security group tag number assigned to each port on a network
Answer: D
Explanation:
Cisco TrustSec uses tags to represent logical group privilege. This tag, called a Security Group Tag
(SGT), is used in access policies. The SGT is understood and is used to enforce traffic by Cisco switches, routers and firewalls . Cisco TrustSec is defined in three phases: classification, propagation and enforcement.
When users and devices connect to a network, the network assigns a specific security group.
This process is called classification. Classification can be based on the results of the authentication or by associating the SGT with an IP, VLAN, or port-profile (-> Answer A and answer C are not correct as they say "assigned ... on a switch" only. Answer D is not correct either as it says "assigned to each router").
QUESTION NO: 5
Refer to the exhibit. A port channel is configured between SW2 and SW3. SW2 is not running a
Cisco operating system. When all physical connections are mode, the port channel does not establish.
Based on the configuration excerpt of SW3, what is the cause of the problem?
A. The port-channel interface lead balance should be set to src-mac
B. The port-channel trunk is not allowing the native VLAN.
C. The port-channel should be set to auto.
D. The port channel on SW2 is using an incompatible protocol.
Answer: D
Explanation:
The Cisco switch was configured with PAgP, which is a Cisco proprietary protocol so non-Cisco switch could not communicate.
現在IT技術会社に通勤しているあなたは、CiscoのMicrosoft AZ-700試験認定を取得しましたか？Microsoft AZ-700試験認定は給料の増加とジョブのプロモーションに役立ちます。 Omgzlookは先輩の経験を生かして暦年の試験の材料を編集することを通して、最高のMicrosoft AI-102J問題集を作成しました。 だから、我々社は力の限りで弊社のCisco VMware 2V0-12.24試験資料を改善し、改革の変更に応じて更新します。 SAP C_THR88_2405 - うちの商品を使ったら、君は最も早い時間で、簡単に認定試験に合格することができます。 あなたはAmazon AI1-C01試験に不安を持っていますか？Amazon AI1-C01参考資料をご覧下さい。
Updated: May 28, 2022