Cisco 350-401日本語版試験解答認定資格試験が難しいので、弊社の350-401日本語版試験解答問題集はあなたに適当する認定資格試験問題集を見つけるし、本当の試験問題の難しさを克服することができます。弊社はCisco 350-401日本語版試験解答認定試験の最新要求に従って関心を持って、全面的かつ高品質な模擬試験問題集を提供します。また、購入する前に、無料で350-401日本語版試験解答のPDF版デモをダウンロードでき、信頼性を確認することができます。 君がCiscoの350-401日本語版試験解答問題集を購入したら、私たちは一年間で無料更新サービスを提供することができます。もしCiscoの350-401日本語版試験解答問題集は問題があれば、或いは試験に不合格になる場合は、全額返金することを保証いたします。 こうして、弊社の商品はどのくらいあなたの力になるのはよく分かっています。
CCNP Enterprise 350-401 給料を倍増させることも不可能ではないです。
CCNP Enterprise 350-401日本語版試験解答 - Implementing Cisco Enterprise Network Core Technologies (350-401 ENCOR) あなたはいつでもサブスクリプションの期間を延長することができますから、より多くの時間を取って充分に試験を準備できます。 それがもう現代生活の不可欠な一部となりました。その中で、Ciscoの認証資格は広範な国際的な認可を得ました。
Ciscoの350-401日本語版試験解答認定試験に受かるのはあなたの技能を検証することだけでなく、あなたの専門知識を証明できて、上司は無駄にあなたを雇うことはしないことの証明書です。当面、IT業界でCiscoの350-401日本語版試験解答認定試験の信頼できるソースが必要です。Omgzlookはとても良い選択で、350-401日本語版試験解答の試験を最も短い時間に縮められますから、あなたの費用とエネルギーを節約することができます。
Cisco 350-401日本語版試験解答 - でも、利用したことがありますか。
Omgzlookは優れたIT情報のソースを提供するサイトです。Omgzlookで、あなたの試験のためのテクニックと勉強資料を見つけることができます。OmgzlookのCiscoの350-401日本語版試験解答試験トレーニング資料は豊富な知識と経験を持っているIT専門家に研究された成果で、正確度がとても高いです。Omgzlookに会ったら、最高のトレーニング資料を見つけました。OmgzlookのCiscoの350-401日本語版試験解答試験トレーニング資料を持っていたら、試験に対する充分の準備がありますから、安心に利用したください。
そして、その学習教材の内容はカバー率が高くて、正確率も高いです。それはきっと君のCiscoの350-401日本語版試験解答試験に合格することの良い参考資料です。
350-401 PDF DEMO:
QUESTION NO: 1
To increase total throughput and redundancy on the links between the wireless controller and switch, the customer enabled LAG on the wireless controller.
Which EtherChannel mode must be configured on the switch to allow the WLC to connect?
A. Active
B. On
C. Auto
D. Passive
Answer: B
Explanation:
Restrictions for Link Aggregation:
You can bundle all eight ports on a Cisco 5508 Controller into a single link.
Terminating on two different modules within a single Catalyst 6500 series switch provides redundancy and ensures that connectivity between the switch and the controller is maintained when one module fails. The controller's port 1 is connected to Gigabit interface 3/1, and the controller's port 2 is connected to Gigabit interface 2/1 on the Catalyst 6500 series switch. Both switch ports are assigned to the same channel group.
LAG requires the EtherChannel to be configured for 'mode on' on both the controller and the Catalyst switch.
Once the EtherChannel is configured as on at both ends of the link, the Catalyst switch should not be configured for either Link Aggregation Control Protocol (LACP) or Cisco proprietary Port Aggregation
Protocol (PAgP) but be set unconditionally to LAG. Because no channel negotiation is done between the controller and the switch, the controller does not answer to negotiation frames and the LAG is not formed if a dynamic form of LAG is set on the switch. Additionally, LACP and PAgP are not supported on the controller.
If the recommended load-balancing method cannot be configured on the Catalyst switch, then configure the LAG connection as a single member link or disable LAG on the controller.
https://www.cisco.com/c/en/us/td/docs/wireless/controller/7-5/configuration- guide/b_cg75/b_cg75_chapter_0100010.html
QUESTION NO: 2
Which technology provides a secure communication channel for all traffic at Layer 2 of the OSI model?
A. IPsec
B. Cisco Trustsec
C. MACsec
D. SSL
Answer: C
Explanation:
MACsec, defined in 802.1AE, provides MAC-layer encryption over wired networks by using out- of
-band methods for encryption keying. The MACsec Key Agreement (MKA) Protocol provides the required session keys and manages the required encryption keys. MKA and MACsec are implemented after successful authentication using the 802.1x Extensible Authentication Protocol (EAP-TLS) or Pre
Shared Key (PSK) framework.
A switch using MACsec accepts either MACsec or non-MACsec frames, depending on the policy associated with the MKA peer. MACsec frames are encrypted and protected with an integrity check value (ICV). When the switch receives frames from the MKA peer, it decrypts them and calculates the correct ICV by using session keys provided by MKA. The switch compares that ICV to the ICV within the frame. If they are not identical, the frame is dropped. The switch also encrypts and adds an ICV to any frames sent over the secured port (the access point used to provide the secure MAC service to a
MKA peer) using the current session key.
Reference: https://www.cisco.com/c/en/us/td/docs/switches/lan/catalyst9300/software/release/16-
9/configuration_guide/sec/b_169_sec_9300_cg/macsec_encryption.html
Note: Cisco Trustsec is the solution which includes MACsec.
QUESTION NO: 3
Refer to the exhibit. A port channel is configured between SW2 and SW3. SW2 is not running a
Cisco operating system. When all physical connections are mode, the port channel does not establish.
Based on the configuration excerpt of SW3, what is the cause of the problem?
A. The port-channel interface lead balance should be set to src-mac
B. The port-channel trunk is not allowing the native VLAN.
C. The port-channel should be set to auto.
D. The port channel on SW2 is using an incompatible protocol.
Answer: D
Explanation:
The Cisco switch was configured with PAgP, which is a Cisco proprietary protocol so non-Cisco switch could not communicate.
QUESTION NO: 4
What is the difference between a RIB and a FIB?
A. The FIB is populated based on RIB content
B. The RIB is used to make IP source prefix-based switching decisions
C. The RIB maintains a mirror image of the FIB
D. The FIB is where all IP routing information is stored
Answer: A
Explanation:
CEF uses a Forwarding Information Base (FIB) to make IP destination prefix-based switching decisions.
The FIB is conceptually similar to a routing table or information base. It maintains a mirror image of the forwarding information contained in the IP routing table. When routing or topology changes occur in the network, the IP routing table is updated, and those changes are reflected in the FIB. The
FIB maintains next-hop address information based on the information in the IP routing table. Because there is a one-to-one correlation between FIB entries and routing table entries, the FIB contains all known routes and eliminates the need for route cache maintenance that is associated with earlier switching paths such as fast switching and optimum switching.
Note: In order to view the Routing information base (RIB) table, use the "show ip route" command.
To view the Forwarding Information Base (FIB), use the "show ip cef" command. RIB is in Control plane while FIB is in Data plane.
QUESTION NO: 5
Which statement about multicast RPs is true?
A. RPs are required for protocol independent multicast sparse mode and dense mode.
B. By default, the RP is needed only to start new sessions with sources and receivers.
C. By default, the RP is needed periodically to maintain sessions with sources and receivers
D. RPs are required only when using protocol independent multicast dense mode.
Answer: B
Explanation:
A rendezvous point (RP) is required only in networks running Protocol Independent Multicast sparse mode (PIM-SM).
By default, the RP is needed only to start new sessions with sources and receivers.
Reference:
https://www.cisco.com/c/en/us/td/docs/ios/solutions_docs/ip_multicast/White_papers/rps.html
For your information, in PIM-SM, only network segments with active receivers that have explicitly requested multicast data will be forwarded the traffic. This method of delivering multicast data is in contrast to the PIM dense mode (PIM-DM) model. In PIM-DM, multicast traffic is initially flooded to all segments of the network. Routers that have no downstream neighbors or directly connected receivers prune back the unwanted traffic.
Microsoft MB-500J - これは試験の準備をするために非常に効率的なツールですから。 EMC D-PDD-OE-23 - まだなにを待っていますか。 SASInstitute A00-451 - 気楽に試験に合格したければ、はやく試しに来てください。 Omgzlookの CiscoのEMC D-PVM-DS-23試験トレーニング資料は高度に認証されたIT領域の専門家の経験と創造を含めているものです。 Salesforce CRT-251-JPN - ここには、私たちは君の需要に応じます。
Updated: May 28, 2022