あなたに向いていることを確かめてから買うのも遅くないですよ。あなたが決して後悔しないことを保証します。OmgzlookのCiscoの350-401日本語版参考資料の試験問題は同じシラバスに従って、実際のCiscoの350-401日本語版参考資料認証試験にも従っています。 なぜならば、弊社は高品質かつ改革によってすぐに更新できる350-401日本語版参考資料問題集を提供できるからです。弊社の350-401日本語版参考資料問題集は大勢の専門家たちの努力で開発される成果です。 Omgzlookはとても良い選択で、350-401日本語版参考資料の試験を最も短い時間に縮められますから、あなたの費用とエネルギーを節約することができます。
CCNP Enterprise 350-401 君の初めての合格を目標にします。
うちのCiscoの350-401 - Implementing Cisco Enterprise Network Core Technologies (350-401 ENCOR)日本語版参考資料試験トレーニング資料を購入する前に、Omgzlookのサイトで、一部分のフリーな試験問題と解答をダンロードでき、試用してみます。 それは確かにそうですが、その知識を身につけることは難しくないとといわれています。IT業界ではさらに強くなるために強い専門知識が必要です。
我々の目的はあなたにCiscoの350-401日本語版参考資料試験に合格することだけです。試験に失敗したら、弊社は全額で返金します。我々の誠意を信じてください。
Cisco 350-401日本語版参考資料 - それは確かに君の試験に役に立つとみられます。
世の中に去年の自分より今年の自分が優れていないのは立派な恥です。それで、IT人材として毎日自分を充実して、350-401日本語版参考資料問題集を学ぶ必要があります。弊社の350-401日本語版参考資料問題集はあなたにこのチャンスを全面的に与えられます。あなたは自分の望ましいCisco 350-401日本語版参考資料問題集を選らんで、学びから更なる成長を求められます。心はもはや空しくなく、生活を美しくなります。
が、サイトに相関する依頼できる保証が何一つありません。ここで私が言いたいのはOmgzlookのコアバリューです。
350-401 PDF DEMO:
QUESTION NO: 1
Which technology provides a secure communication channel for all traffic at Layer 2 of the OSI model?
A. IPsec
B. Cisco Trustsec
C. MACsec
D. SSL
Answer: C
Explanation:
MACsec, defined in 802.1AE, provides MAC-layer encryption over wired networks by using out- of
-band methods for encryption keying. The MACsec Key Agreement (MKA) Protocol provides the required session keys and manages the required encryption keys. MKA and MACsec are implemented after successful authentication using the 802.1x Extensible Authentication Protocol (EAP-TLS) or Pre
Shared Key (PSK) framework.
A switch using MACsec accepts either MACsec or non-MACsec frames, depending on the policy associated with the MKA peer. MACsec frames are encrypted and protected with an integrity check value (ICV). When the switch receives frames from the MKA peer, it decrypts them and calculates the correct ICV by using session keys provided by MKA. The switch compares that ICV to the ICV within the frame. If they are not identical, the frame is dropped. The switch also encrypts and adds an ICV to any frames sent over the secured port (the access point used to provide the secure MAC service to a
MKA peer) using the current session key.
Reference: https://www.cisco.com/c/en/us/td/docs/switches/lan/catalyst9300/software/release/16-
9/configuration_guide/sec/b_169_sec_9300_cg/macsec_encryption.html
Note: Cisco Trustsec is the solution which includes MACsec.
QUESTION NO: 2
Refer to the exhibit. A port channel is configured between SW2 and SW3. SW2 is not running a
Cisco operating system. When all physical connections are mode, the port channel does not establish.
Based on the configuration excerpt of SW3, what is the cause of the problem?
A. The port-channel interface lead balance should be set to src-mac
B. The port-channel trunk is not allowing the native VLAN.
C. The port-channel should be set to auto.
D. The port channel on SW2 is using an incompatible protocol.
Answer: D
Explanation:
The Cisco switch was configured with PAgP, which is a Cisco proprietary protocol so non-Cisco switch could not communicate.
QUESTION NO: 3
To increase total throughput and redundancy on the links between the wireless controller and switch, the customer enabled LAG on the wireless controller.
Which EtherChannel mode must be configured on the switch to allow the WLC to connect?
A. Active
B. On
C. Auto
D. Passive
Answer: B
Explanation:
Restrictions for Link Aggregation:
You can bundle all eight ports on a Cisco 5508 Controller into a single link.
Terminating on two different modules within a single Catalyst 6500 series switch provides redundancy and ensures that connectivity between the switch and the controller is maintained when one module fails. The controller's port 1 is connected to Gigabit interface 3/1, and the controller's port 2 is connected to Gigabit interface 2/1 on the Catalyst 6500 series switch. Both switch ports are assigned to the same channel group.
LAG requires the EtherChannel to be configured for 'mode on' on both the controller and the Catalyst switch.
Once the EtherChannel is configured as on at both ends of the link, the Catalyst switch should not be configured for either Link Aggregation Control Protocol (LACP) or Cisco proprietary Port Aggregation
Protocol (PAgP) but be set unconditionally to LAG. Because no channel negotiation is done between the controller and the switch, the controller does not answer to negotiation frames and the LAG is not formed if a dynamic form of LAG is set on the switch. Additionally, LACP and PAgP are not supported on the controller.
If the recommended load-balancing method cannot be configured on the Catalyst switch, then configure the LAG connection as a single member link or disable LAG on the controller.
https://www.cisco.com/c/en/us/td/docs/wireless/controller/7-5/configuration- guide/b_cg75/b_cg75_chapter_0100010.html
QUESTION NO: 4
Which statement about multicast RPs is true?
A. RPs are required for protocol independent multicast sparse mode and dense mode.
B. By default, the RP is needed only to start new sessions with sources and receivers.
C. By default, the RP is needed periodically to maintain sessions with sources and receivers
D. RPs are required only when using protocol independent multicast dense mode.
Answer: B
Explanation:
A rendezvous point (RP) is required only in networks running Protocol Independent Multicast sparse mode (PIM-SM).
By default, the RP is needed only to start new sessions with sources and receivers.
Reference:
https://www.cisco.com/c/en/us/td/docs/ios/solutions_docs/ip_multicast/White_papers/rps.html
For your information, in PIM-SM, only network segments with active receivers that have explicitly requested multicast data will be forwarded the traffic. This method of delivering multicast data is in contrast to the PIM dense mode (PIM-DM) model. In PIM-DM, multicast traffic is initially flooded to all segments of the network. Routers that have no downstream neighbors or directly connected receivers prune back the unwanted traffic.
QUESTION NO: 5
What is the difference between a RIB and a FIB?
A. The FIB is populated based on RIB content
B. The RIB is used to make IP source prefix-based switching decisions
C. The RIB maintains a mirror image of the FIB
D. The FIB is where all IP routing information is stored
Answer: A
Explanation:
CEF uses a Forwarding Information Base (FIB) to make IP destination prefix-based switching decisions.
The FIB is conceptually similar to a routing table or information base. It maintains a mirror image of the forwarding information contained in the IP routing table. When routing or topology changes occur in the network, the IP routing table is updated, and those changes are reflected in the FIB. The
FIB maintains next-hop address information based on the information in the IP routing table. Because there is a one-to-one correlation between FIB entries and routing table entries, the FIB contains all known routes and eliminates the need for route cache maintenance that is associated with earlier switching paths such as fast switching and optimum switching.
Note: In order to view the Routing information base (RIB) table, use the "show ip route" command.
To view the Forwarding Information Base (FIB), use the "show ip cef" command. RIB is in Control plane while FIB is in Data plane.
また、EMC D-PDD-OE-23問題集に疑問があると、メールで問い合わせてください。 我々はCiscoのSAP C_THR92_2405試験問題と解答また試験シミュレータを最初に提供し始めたとき、私達が評判を取ることを夢にも思わなかった。 人によって目標が違いますが、あなたにCisco CIW 1D0-671試験に順調に合格できるのは我々の共同の目標です。 SAP C-THR97-2405 - これは受験生の皆様を助けた結果です。 あなたに高品質で、全面的なISQI CTFL-Foundation参考資料を提供することは私たちの責任です。
Updated: May 28, 2022