あなたはインターネットでCiscoの350-401専門トレーリング認証試験の練習問題と解答の試用版を無料でダウンロードしてください。そうしたらあなたはOmgzlookが用意した問題集にもっと自信があります。早くOmgzlookの問題集を君の手に入れましょう。 Omgzlook は各受験生のニーズを知っていて、あなたが350-401専門トレーリング認定試験に受かることに有効なヘルプを差し上げます。あなたが首尾よく試験に合格するように、我々は最も有利な価格と最高のクオリティーを提供して差し上げます。 OmgzlookにIT業界のエリートのグループがあって、彼達は自分の経験と専門知識を使ってCisco 350-401専門トレーリング認証試験に参加する方に対して問題集を研究続けています。
CCNP Enterprise 350-401 不思議を思っていますか。
問題が更新される限り、Omgzlookは直ちに最新版の350-401 - Implementing Cisco Enterprise Network Core Technologies (350-401 ENCOR)専門トレーリング資料を送ってあげます。 350-401 技術問題試験の準備をするとき、がむしゃらにITに関連する知識を学ぶのは望ましくない勉強法です。実際は試験に合格するコツがあるのですよ。
Omgzlookの350-401専門トレーリング問題集は多くの受験生に検証されたものですから、高い成功率を保証できます。もしこの問題集を利用してからやはり試験に不合格になってしまえば、Omgzlookは全額で返金することができます。あるいは、無料で試験350-401専門トレーリング問題集を更新してあげるのを選択することもできます。
Cisco 350-401専門トレーリング - 君の明るい将来を祈っています。
OmgzlookのCiscoの350-401専門トレーリング認証試験について最新な研究を完成いたしました。無料な部分ダウンロードしてください。きっと君に失望させないと信じています。最新Ciscoの350-401専門トレーリング認定試験は真実の試験問題にもっとも近くて比較的に全面的でございます。
それは確かにそうですが、その知識を身につけることは難しくないとといわれています。IT業界ではさらに強くなるために強い専門知識が必要です。
350-401 PDF DEMO:
QUESTION NO: 1
Refer to the exhibit. A port channel is configured between SW2 and SW3. SW2 is not running a
Cisco operating system. When all physical connections are mode, the port channel does not establish.
Based on the configuration excerpt of SW3, what is the cause of the problem?
A. The port-channel interface lead balance should be set to src-mac
B. The port-channel trunk is not allowing the native VLAN.
C. The port-channel should be set to auto.
D. The port channel on SW2 is using an incompatible protocol.
Answer: D
Explanation:
The Cisco switch was configured with PAgP, which is a Cisco proprietary protocol so non-Cisco switch could not communicate.
QUESTION NO: 2
Which technology provides a secure communication channel for all traffic at Layer 2 of the OSI model?
A. IPsec
B. Cisco Trustsec
C. MACsec
D. SSL
Answer: C
Explanation:
MACsec, defined in 802.1AE, provides MAC-layer encryption over wired networks by using out- of
-band methods for encryption keying. The MACsec Key Agreement (MKA) Protocol provides the required session keys and manages the required encryption keys. MKA and MACsec are implemented after successful authentication using the 802.1x Extensible Authentication Protocol (EAP-TLS) or Pre
Shared Key (PSK) framework.
A switch using MACsec accepts either MACsec or non-MACsec frames, depending on the policy associated with the MKA peer. MACsec frames are encrypted and protected with an integrity check value (ICV). When the switch receives frames from the MKA peer, it decrypts them and calculates the correct ICV by using session keys provided by MKA. The switch compares that ICV to the ICV within the frame. If they are not identical, the frame is dropped. The switch also encrypts and adds an ICV to any frames sent over the secured port (the access point used to provide the secure MAC service to a
MKA peer) using the current session key.
Reference: https://www.cisco.com/c/en/us/td/docs/switches/lan/catalyst9300/software/release/16-
9/configuration_guide/sec/b_169_sec_9300_cg/macsec_encryption.html
Note: Cisco Trustsec is the solution which includes MACsec.
QUESTION NO: 3
Which statement about multicast RPs is true?
A. RPs are required for protocol independent multicast sparse mode and dense mode.
B. By default, the RP is needed only to start new sessions with sources and receivers.
C. By default, the RP is needed periodically to maintain sessions with sources and receivers
D. RPs are required only when using protocol independent multicast dense mode.
Answer: B
Explanation:
A rendezvous point (RP) is required only in networks running Protocol Independent Multicast sparse mode (PIM-SM).
By default, the RP is needed only to start new sessions with sources and receivers.
Reference:
https://www.cisco.com/c/en/us/td/docs/ios/solutions_docs/ip_multicast/White_papers/rps.html
For your information, in PIM-SM, only network segments with active receivers that have explicitly requested multicast data will be forwarded the traffic. This method of delivering multicast data is in contrast to the PIM dense mode (PIM-DM) model. In PIM-DM, multicast traffic is initially flooded to all segments of the network. Routers that have no downstream neighbors or directly connected receivers prune back the unwanted traffic.
QUESTION NO: 4
To increase total throughput and redundancy on the links between the wireless controller and switch, the customer enabled LAG on the wireless controller.
Which EtherChannel mode must be configured on the switch to allow the WLC to connect?
A. Active
B. On
C. Auto
D. Passive
Answer: B
Explanation:
Restrictions for Link Aggregation:
You can bundle all eight ports on a Cisco 5508 Controller into a single link.
Terminating on two different modules within a single Catalyst 6500 series switch provides redundancy and ensures that connectivity between the switch and the controller is maintained when one module fails. The controller's port 1 is connected to Gigabit interface 3/1, and the controller's port 2 is connected to Gigabit interface 2/1 on the Catalyst 6500 series switch. Both switch ports are assigned to the same channel group.
LAG requires the EtherChannel to be configured for 'mode on' on both the controller and the Catalyst switch.
Once the EtherChannel is configured as on at both ends of the link, the Catalyst switch should not be configured for either Link Aggregation Control Protocol (LACP) or Cisco proprietary Port Aggregation
Protocol (PAgP) but be set unconditionally to LAG. Because no channel negotiation is done between the controller and the switch, the controller does not answer to negotiation frames and the LAG is not formed if a dynamic form of LAG is set on the switch. Additionally, LACP and PAgP are not supported on the controller.
If the recommended load-balancing method cannot be configured on the Catalyst switch, then configure the LAG connection as a single member link or disable LAG on the controller.
https://www.cisco.com/c/en/us/td/docs/wireless/controller/7-5/configuration- guide/b_cg75/b_cg75_chapter_0100010.html
QUESTION NO: 5
Which access controls list allows only TCP traffic with a destination port range of 22-433, excluding port 80?
A. Deny tcp any any ne 80
Permit tcp any any range 22 443
B. Permit tcp any any ne 80
C. Permit tco any any range 22 443
Deny tcp any any eq 80
D. Deny tcp any any eq 80
Permit tco any any gt 21 it 444
Answer: D
インターネットで時勢に遅れないLpi 102-500勉強資料を提供するというサイトがあるかもしれませんが、Omgzlookはあなたに高品質かつ最新のCiscoのLpi 102-500トレーニング資料を提供するユニークなサイトです。 Omgzlookが提供したCiscoのMicrosoft MB-310「Implementing Cisco Enterprise Network Core Technologies (350-401 ENCOR)」試験問題と解答が真実の試験の練習問題と解答は最高の相似性があり、一年の無料オンラインの更新のサービスがあり、100%のパス率を保証して、もし試験に合格しないと、弊社は全額で返金いたします。 Microsoft MB-260 - ためらわずに速くあなたのショッピングカートに入れてください。 MuleSoft MCD-Level-2 - 使用して私たちOmgzlookが提供した対応性練習問題が君にとってはなかなかよいサイトだと思います。 OmgzlookのCiscoのIBM C1000-101-KR試験トレーニング資料はインターネットでの全てのトレーニング資料のリーダーです。
Updated: May 28, 2022