自分のIT業界での発展を希望したら、Ciscoの350-401学習体験談試験に合格する必要があります。Ciscoの350-401学習体験談試験はいくつ難しくても文句を言わないで、我々Omgzlookの提供する資料を通して、あなたはCiscoの350-401学習体験談試験に合格することができます。Ciscoの350-401学習体験談試験を準備しているあなたに試験に合格させるために、我々Omgzlookは模擬試験ソフトを更新し続けています。 ご購入した一年間、あなたはCiscoの350-401学習体験談ソフトの最新の資料を無料で得られます。品質は、時間と量の試練に耐えることです。 弊社の350-401学習体験談問題集はあなたにこのチャンスを全面的に与えられます。
CCNP Enterprise 350-401 弊社の商品が好きなのは弊社のたのしいです。
CCNP Enterprise 350-401学習体験談 - Implementing Cisco Enterprise Network Core Technologies (350-401 ENCOR) 躊躇わなくて、Omgzlookサイト情報を早く了解して、あなたに試験合格を助かってあげますようにお願いいたします。 Omgzlook を選択して１００％の合格率を確保することができて、もし試験に失敗したら、Omgzlookが全額で返金いたします。
多くのお客様は私たちCisco 350-401学習体験談クイズに十分な信頼を持っています。Cisco 350-401学習体験談試験問題のデモを無料でダウンロードできます。そうすれば、自分は350-401学習体験談試験問題集を買うかどうか決めることができます。
Cisco 350-401学習体験談 - Omgzlookを選んだら、成功への扉を開きます。
Omgzlookは異なるトレーニングツールと資源を提供してあなたのCiscoの350-401学習体験談の認証試験の準備にヘルプを差し上げます。編成チュートリアルは授業コース、実践検定、試験エンジンと一部の無料なPDFダウンロードを含めています。
したがって、Omgzlookの350-401学習体験談問題集も絶えずに更新されています。それに、Omgzlookの教材を購入すれば、Omgzlookは一年間の無料アップデート・サービスを提供してあげます。
350-401 PDF DEMO:
QUESTION NO: 1
What is the difference between a RIB and a FIB?
A. The FIB is populated based on RIB content
B. The RIB is used to make IP source prefix-based switching decisions
C. The RIB maintains a mirror image of the FIB
D. The FIB is where all IP routing information is stored
Answer: A
Explanation:
CEF uses a Forwarding Information Base (FIB) to make IP destination prefix-based switching decisions.
The FIB is conceptually similar to a routing table or information base. It maintains a mirror image of the forwarding information contained in the IP routing table. When routing or topology changes occur in the network, the IP routing table is updated, and those changes are reflected in the FIB. The
FIB maintains next-hop address information based on the information in the IP routing table. Because there is a one-to-one correlation between FIB entries and routing table entries, the FIB contains all known routes and eliminates the need for route cache maintenance that is associated with earlier switching paths such as fast switching and optimum switching.
Note: In order to view the Routing information base (RIB) table, use the "show ip route" command.
To view the Forwarding Information Base (FIB), use the "show ip cef" command. RIB is in Control plane while FIB is in Data plane.
QUESTION NO: 2
To increase total throughput and redundancy on the links between the wireless controller and switch, the customer enabled LAG on the wireless controller.
Which EtherChannel mode must be configured on the switch to allow the WLC to connect?
A. Active
B. On
C. Auto
D. Passive
Answer: B
Explanation:
Restrictions for Link Aggregation:
You can bundle all eight ports on a Cisco 5508 Controller into a single link.
Terminating on two different modules within a single Catalyst 6500 series switch provides redundancy and ensures that connectivity between the switch and the controller is maintained when one module fails. The controller's port 1 is connected to Gigabit interface 3/1, and the controller's port 2 is connected to Gigabit interface 2/1 on the Catalyst 6500 series switch. Both switch ports are assigned to the same channel group.
LAG requires the EtherChannel to be configured for 'mode on' on both the controller and the Catalyst switch.
Once the EtherChannel is configured as on at both ends of the link, the Catalyst switch should not be configured for either Link Aggregation Control Protocol (LACP) or Cisco proprietary Port Aggregation
Protocol (PAgP) but be set unconditionally to LAG. Because no channel negotiation is done between the controller and the switch, the controller does not answer to negotiation frames and the LAG is not formed if a dynamic form of LAG is set on the switch. Additionally, LACP and PAgP are not supported on the controller.
If the recommended load-balancing method cannot be configured on the Catalyst switch, then configure the LAG connection as a single member link or disable LAG on the controller.
https://www.cisco.com/c/en/us/td/docs/wireless/controller/7-5/configuration- guide/b_cg75/b_cg75_chapter_0100010.html
QUESTION NO: 3
Which technology provides a secure communication channel for all traffic at Layer 2 of the OSI model?
A. IPsec
B. Cisco Trustsec
C. MACsec
D. SSL
Answer: C
Explanation:
MACsec, defined in 802.1AE, provides MAC-layer encryption over wired networks by using out- of
-band methods for encryption keying. The MACsec Key Agreement (MKA) Protocol provides the required session keys and manages the required encryption keys. MKA and MACsec are implemented after successful authentication using the 802.1x Extensible Authentication Protocol (EAP-TLS) or Pre
Shared Key (PSK) framework.
A switch using MACsec accepts either MACsec or non-MACsec frames, depending on the policy associated with the MKA peer. MACsec frames are encrypted and protected with an integrity check value (ICV). When the switch receives frames from the MKA peer, it decrypts them and calculates the correct ICV by using session keys provided by MKA. The switch compares that ICV to the ICV within the frame. If they are not identical, the frame is dropped. The switch also encrypts and adds an ICV to any frames sent over the secured port (the access point used to provide the secure MAC service to a
MKA peer) using the current session key.
Reference: https://www.cisco.com/c/en/us/td/docs/switches/lan/catalyst9300/software/release/16-
9/configuration_guide/sec/b_169_sec_9300_cg/macsec_encryption.html
Note: Cisco Trustsec is the solution which includes MACsec.
QUESTION NO: 4
Which feature does Cisco TrustSec use to provide scalable, secure communication throughout a network?
A. security group tag number assigned to each user on a switch
B. security group tag ACL assigned to each router on a network
C. security group tag ACL assigned to each port on a switch
D. security group tag number assigned to each port on a network
Answer: D
Explanation:
Cisco TrustSec uses tags to represent logical group privilege. This tag, called a Security Group Tag
(SGT), is used in access policies. The SGT is understood and is used to enforce traffic by Cisco switches, routers and firewalls . Cisco TrustSec is defined in three phases: classification, propagation and enforcement.
When users and devices connect to a network, the network assigns a specific security group.
This process is called classification. Classification can be based on the results of the authentication or by associating the SGT with an IP, VLAN, or port-profile (-> Answer A and answer C are not correct as they say "assigned ... on a switch" only. Answer D is not correct either as it says "assigned to each router").
QUESTION NO: 5
Refer to the exhibit. A port channel is configured between SW2 and SW3. SW2 is not running a
Cisco operating system. When all physical connections are mode, the port channel does not establish.
Based on the configuration excerpt of SW3, what is the cause of the problem?
A. The port-channel interface lead balance should be set to src-mac
B. The port-channel trunk is not allowing the native VLAN.
C. The port-channel should be set to auto.
D. The port channel on SW2 is using an incompatible protocol.
Answer: D
Explanation:
The Cisco switch was configured with PAgP, which is a Cisco proprietary protocol so non-Cisco switch could not communicate.
SAP C-TS4FI-2023 - Omgzlookはあなたにとって最も正確な選択ですから。 OmgzlookのNetwork Appliance NS0-604問題集は多くの受験生に検証されたものですから、高い成功率を保証できます。 Omgzlookが提供したCiscoのAvaya 71402X「Implementing Cisco Enterprise Network Core Technologies (350-401 ENCOR)」試験トレーニング資料はあなたが試験に合格することを助けられます。 OmgzlookのITエリートたちは彼らの専門的な目で、最新的なCiscoのIBM C1000-173試験トレーニング資料に注目していて、うちのCiscoのIBM C1000-173問題集の高い正確性を保証するのです。 Google Cloud-Digital-Leader-JPN - Omgzlookが提供した製品がIT専門家は実際の経験を活かして作った最も良い製品で、あなたが自分の目標を達成するようにずっと一生懸命頑張っています。
Updated: May 28, 2022