Omgzlookはきみの貴重な時間を節約するだけでなく、 安心で順調に試験に合格するのを保証します。Omgzlookは専門のIT業界での評判が高くて、あなたがインターネットでOmgzlookの部分のCisco 350-401問題集「Implementing Cisco Enterprise Network Core Technologies (350-401 ENCOR)」資料を無料でダウンロードして、弊社の正確率を確認してください。弊社の商品が好きなのは弊社のたのしいです。 最近、Ciscoの350-401問題集試験は非常に人気のある認定試験です。あなたもこの試験の認定資格を取得したいのですか。 Omgzlookの商品はとても頼もしい試験の練習問題と解答は非常に正確でございます。
それはOmgzlookの350-401問題集問題集です。
弊社Omgzlookの350-401 - Implementing Cisco Enterprise Network Core Technologies (350-401 ENCOR)問題集試験問題集を介して、速く試験に合格して350-401 - Implementing Cisco Enterprise Network Core Technologies (350-401 ENCOR)問題集試験資格認定書を受け入れる一方で、他の人が知らない知識を勉強して優れる人になることに近くなります。 Omgzlookは君にとってベストな選択になります。ここには、私たちは君の需要に応じます。
弊社のCisco 350-401問題集問題集を使用した後、350-401問題集試験に合格するのはあまりに難しくないことだと知られます。我々Omgzlook提供する350-401問題集問題集を通して、試験に迅速的にパースする技をファンドできます。あなたのご遠慮なく購買するために、弊社は提供する無料のCisco 350-401問題集問題集デーモをダウンロードします。
Cisco 350-401問題集 - 我々の誠意を信じてください。
現在の社会で、350-401問題集試験に参加する人がますます多くなる傾向があります。市場の巨大な練習材料から350-401問題集の学習教材を手に入れようとする人も増えています。 私たちの350-401問題集試験問題を利用し、ほかの資料が克服できない障害を克服できます。 多くの受験者は、私たちの350-401問題集練習試験をすることに特権を感じています。 そして、私たちのウェブサイトは、市場でのとても有名で、インターネット上で簡単に見つけられます。
自分のIT業界での発展を希望したら、Ciscoの350-401問題集試験に合格する必要があります。Ciscoの350-401問題集試験はいくつ難しくても文句を言わないで、我々Omgzlookの提供する資料を通して、あなたはCiscoの350-401問題集試験に合格することができます。
350-401 PDF DEMO:
QUESTION NO: 1
Which technology provides a secure communication channel for all traffic at Layer 2 of the OSI model?
A. IPsec
B. Cisco Trustsec
C. MACsec
D. SSL
Answer: C
Explanation:
MACsec, defined in 802.1AE, provides MAC-layer encryption over wired networks by using out- of
-band methods for encryption keying. The MACsec Key Agreement (MKA) Protocol provides the required session keys and manages the required encryption keys. MKA and MACsec are implemented after successful authentication using the 802.1x Extensible Authentication Protocol (EAP-TLS) or Pre
Shared Key (PSK) framework.
A switch using MACsec accepts either MACsec or non-MACsec frames, depending on the policy associated with the MKA peer. MACsec frames are encrypted and protected with an integrity check value (ICV). When the switch receives frames from the MKA peer, it decrypts them and calculates the correct ICV by using session keys provided by MKA. The switch compares that ICV to the ICV within the frame. If they are not identical, the frame is dropped. The switch also encrypts and adds an ICV to any frames sent over the secured port (the access point used to provide the secure MAC service to a
MKA peer) using the current session key.
Reference: https://www.cisco.com/c/en/us/td/docs/switches/lan/catalyst9300/software/release/16-
9/configuration_guide/sec/b_169_sec_9300_cg/macsec_encryption.html
Note: Cisco Trustsec is the solution which includes MACsec.
QUESTION NO: 2
Refer to the exhibit. A port channel is configured between SW2 and SW3. SW2 is not running a
Cisco operating system. When all physical connections are mode, the port channel does not establish.
Based on the configuration excerpt of SW3, what is the cause of the problem?
A. The port-channel interface lead balance should be set to src-mac
B. The port-channel trunk is not allowing the native VLAN.
C. The port-channel should be set to auto.
D. The port channel on SW2 is using an incompatible protocol.
Answer: D
Explanation:
The Cisco switch was configured with PAgP, which is a Cisco proprietary protocol so non-Cisco switch could not communicate.
QUESTION NO: 3
To increase total throughput and redundancy on the links between the wireless controller and switch, the customer enabled LAG on the wireless controller.
Which EtherChannel mode must be configured on the switch to allow the WLC to connect?
A. Active
B. On
C. Auto
D. Passive
Answer: B
Explanation:
Restrictions for Link Aggregation:
You can bundle all eight ports on a Cisco 5508 Controller into a single link.
Terminating on two different modules within a single Catalyst 6500 series switch provides redundancy and ensures that connectivity between the switch and the controller is maintained when one module fails. The controller's port 1 is connected to Gigabit interface 3/1, and the controller's port 2 is connected to Gigabit interface 2/1 on the Catalyst 6500 series switch. Both switch ports are assigned to the same channel group.
LAG requires the EtherChannel to be configured for 'mode on' on both the controller and the Catalyst switch.
Once the EtherChannel is configured as on at both ends of the link, the Catalyst switch should not be configured for either Link Aggregation Control Protocol (LACP) or Cisco proprietary Port Aggregation
Protocol (PAgP) but be set unconditionally to LAG. Because no channel negotiation is done between the controller and the switch, the controller does not answer to negotiation frames and the LAG is not formed if a dynamic form of LAG is set on the switch. Additionally, LACP and PAgP are not supported on the controller.
If the recommended load-balancing method cannot be configured on the Catalyst switch, then configure the LAG connection as a single member link or disable LAG on the controller.
https://www.cisco.com/c/en/us/td/docs/wireless/controller/7-5/configuration- guide/b_cg75/b_cg75_chapter_0100010.html
QUESTION NO: 4
Which statement about multicast RPs is true?
A. RPs are required for protocol independent multicast sparse mode and dense mode.
B. By default, the RP is needed only to start new sessions with sources and receivers.
C. By default, the RP is needed periodically to maintain sessions with sources and receivers
D. RPs are required only when using protocol independent multicast dense mode.
Answer: B
Explanation:
A rendezvous point (RP) is required only in networks running Protocol Independent Multicast sparse mode (PIM-SM).
By default, the RP is needed only to start new sessions with sources and receivers.
Reference:
https://www.cisco.com/c/en/us/td/docs/ios/solutions_docs/ip_multicast/White_papers/rps.html
For your information, in PIM-SM, only network segments with active receivers that have explicitly requested multicast data will be forwarded the traffic. This method of delivering multicast data is in contrast to the PIM dense mode (PIM-DM) model. In PIM-DM, multicast traffic is initially flooded to all segments of the network. Routers that have no downstream neighbors or directly connected receivers prune back the unwanted traffic.
QUESTION NO: 5
What is the difference between a RIB and a FIB?
A. The FIB is populated based on RIB content
B. The RIB is used to make IP source prefix-based switching decisions
C. The RIB maintains a mirror image of the FIB
D. The FIB is where all IP routing information is stored
Answer: A
Explanation:
CEF uses a Forwarding Information Base (FIB) to make IP destination prefix-based switching decisions.
The FIB is conceptually similar to a routing table or information base. It maintains a mirror image of the forwarding information contained in the IP routing table. When routing or topology changes occur in the network, the IP routing table is updated, and those changes are reflected in the FIB. The
FIB maintains next-hop address information based on the information in the IP routing table. Because there is a one-to-one correlation between FIB entries and routing table entries, the FIB contains all known routes and eliminates the need for route cache maintenance that is associated with earlier switching paths such as fast switching and optimum switching.
Note: In order to view the Routing information base (RIB) table, use the "show ip route" command.
To view the Forwarding Information Base (FIB), use the "show ip cef" command. RIB is in Control plane while FIB is in Data plane.
Microsoft DP-600J - OmgzlookはきみのIT夢に向かって力になりますよ。 EMC D-VXR-DS-00 - 心はもはや空しくなく、生活を美しくなります。 Amazon SAA-C03-KR - 今の多士済々な社会の中で、IT専門人士はとても人気がありますが、競争も大きいです。 短時間でSAP C-ARSOR-2404試験に一発合格したいなら、我々社のCiscoのSAP C-ARSOR-2404資料を参考しましょう。 ISC SSCP - 受験者がOmgzlookを選択したら高度専門の試験に１００％合格することが問題にならないと保証いたします。
Updated: May 28, 2022