最近IT試験を受けて認証資格を取ることは一層重要になりました。たとえばCisco、IBM、Cisco、VMware、SAPなどのいろいろな試験は今では全部非常に重要な試験です。より多くの人々は複数の資格を取得するために多くの350-401問題サンプル試験を受験したいと思っています。 試験問題と解答に関する質問があるなら、当社は直後に解決方法を差し上げます。しかも、一年間の無料更新サービスを提供します。 ですから、はやくOmgzlookの350-401問題サンプル問題集を入手しましょう。
CCNP Enterprise 350-401 でも、成功へのショートカットがを見つけました。
OmgzlookのCiscoの350-401 - Implementing Cisco Enterprise Network Core Technologies (350-401 ENCOR)問題サンプル試験トレーニング資料はIT認証試験を受ける全ての受験生が試験に合格することを助けるもので、受験生からの良い評価をたくさんもらいました。 さて、はやく試験を申し込みましょう。Omgzlookはあなたを助けることができますから、心配する必要がないですよ。
あなたの利用するCiscoの350-401問題サンプルソフトが最新版のを保証するために、一年間の無料更新を提供します。人々は異なる目標がありますが、我々はあなたにCiscoの350-401問題サンプル試験に合格させるという同じ目標があります。この目標を達成するのは、あなたにとってIT分野での第一歩だけですが、我々のCiscoの350-401問題サンプルソフトを開発するすべての意義です。
Cisco 350-401問題サンプル問題集を利用して試験に合格できます。
君はほかのサイトや書籍もブラウズ するがもしれませんが、弊社の関連の学習資料と比較してからOmgzlookの商品の範囲が広くてまたネット上でダウンロードを発見してしまいました。Omgzlookだけ全面と高品質の問題集があるのではOmgzlookの専門家チームが彼らの長年のIT知識と豊富な経験で研究してしました。そして、Omgzlookに多くの受験生の歓迎されます。
Omgzlookは同業の中でそんなに良い地位を取るの原因は弊社のかなり正確な試験の練習問題と解答そえに迅速の更新で、このようにとても良い成績がとられています。そして、弊社が提供した問題集を安心で使用して、試験を安心で受けて、君のCisco 350-401問題サンプル認証試験の１００％の合格率を保証しますす。
350-401 PDF DEMO:
QUESTION NO: 1
Which technology provides a secure communication channel for all traffic at Layer 2 of the OSI model?
A. IPsec
B. Cisco Trustsec
C. MACsec
D. SSL
Answer: C
Explanation:
MACsec, defined in 802.1AE, provides MAC-layer encryption over wired networks by using out- of
-band methods for encryption keying. The MACsec Key Agreement (MKA) Protocol provides the required session keys and manages the required encryption keys. MKA and MACsec are implemented after successful authentication using the 802.1x Extensible Authentication Protocol (EAP-TLS) or Pre
Shared Key (PSK) framework.
A switch using MACsec accepts either MACsec or non-MACsec frames, depending on the policy associated with the MKA peer. MACsec frames are encrypted and protected with an integrity check value (ICV). When the switch receives frames from the MKA peer, it decrypts them and calculates the correct ICV by using session keys provided by MKA. The switch compares that ICV to the ICV within the frame. If they are not identical, the frame is dropped. The switch also encrypts and adds an ICV to any frames sent over the secured port (the access point used to provide the secure MAC service to a
MKA peer) using the current session key.
Reference: https://www.cisco.com/c/en/us/td/docs/switches/lan/catalyst9300/software/release/16-
9/configuration_guide/sec/b_169_sec_9300_cg/macsec_encryption.html
Note: Cisco Trustsec is the solution which includes MACsec.
QUESTION NO: 2
Refer to the exhibit. A port channel is configured between SW2 and SW3. SW2 is not running a
Cisco operating system. When all physical connections are mode, the port channel does not establish.
Based on the configuration excerpt of SW3, what is the cause of the problem?
A. The port-channel interface lead balance should be set to src-mac
B. The port-channel trunk is not allowing the native VLAN.
C. The port-channel should be set to auto.
D. The port channel on SW2 is using an incompatible protocol.
Answer: D
Explanation:
The Cisco switch was configured with PAgP, which is a Cisco proprietary protocol so non-Cisco switch could not communicate.
QUESTION NO: 3
To increase total throughput and redundancy on the links between the wireless controller and switch, the customer enabled LAG on the wireless controller.
Which EtherChannel mode must be configured on the switch to allow the WLC to connect?
A. Active
B. On
C. Auto
D. Passive
Answer: B
Explanation:
Restrictions for Link Aggregation:
You can bundle all eight ports on a Cisco 5508 Controller into a single link.
Terminating on two different modules within a single Catalyst 6500 series switch provides redundancy and ensures that connectivity between the switch and the controller is maintained when one module fails. The controller's port 1 is connected to Gigabit interface 3/1, and the controller's port 2 is connected to Gigabit interface 2/1 on the Catalyst 6500 series switch. Both switch ports are assigned to the same channel group.
LAG requires the EtherChannel to be configured for 'mode on' on both the controller and the Catalyst switch.
Once the EtherChannel is configured as on at both ends of the link, the Catalyst switch should not be configured for either Link Aggregation Control Protocol (LACP) or Cisco proprietary Port Aggregation
Protocol (PAgP) but be set unconditionally to LAG. Because no channel negotiation is done between the controller and the switch, the controller does not answer to negotiation frames and the LAG is not formed if a dynamic form of LAG is set on the switch. Additionally, LACP and PAgP are not supported on the controller.
If the recommended load-balancing method cannot be configured on the Catalyst switch, then configure the LAG connection as a single member link or disable LAG on the controller.
https://www.cisco.com/c/en/us/td/docs/wireless/controller/7-5/configuration- guide/b_cg75/b_cg75_chapter_0100010.html
QUESTION NO: 4
Which statement about multicast RPs is true?
A. RPs are required for protocol independent multicast sparse mode and dense mode.
B. By default, the RP is needed only to start new sessions with sources and receivers.
C. By default, the RP is needed periodically to maintain sessions with sources and receivers
D. RPs are required only when using protocol independent multicast dense mode.
Answer: B
Explanation:
A rendezvous point (RP) is required only in networks running Protocol Independent Multicast sparse mode (PIM-SM).
By default, the RP is needed only to start new sessions with sources and receivers.
Reference:
https://www.cisco.com/c/en/us/td/docs/ios/solutions_docs/ip_multicast/White_papers/rps.html
For your information, in PIM-SM, only network segments with active receivers that have explicitly requested multicast data will be forwarded the traffic. This method of delivering multicast data is in contrast to the PIM dense mode (PIM-DM) model. In PIM-DM, multicast traffic is initially flooded to all segments of the network. Routers that have no downstream neighbors or directly connected receivers prune back the unwanted traffic.
QUESTION NO: 5
What is the difference between a RIB and a FIB?
A. The FIB is populated based on RIB content
B. The RIB is used to make IP source prefix-based switching decisions
C. The RIB maintains a mirror image of the FIB
D. The FIB is where all IP routing information is stored
Answer: A
Explanation:
CEF uses a Forwarding Information Base (FIB) to make IP destination prefix-based switching decisions.
The FIB is conceptually similar to a routing table or information base. It maintains a mirror image of the forwarding information contained in the IP routing table. When routing or topology changes occur in the network, the IP routing table is updated, and those changes are reflected in the FIB. The
FIB maintains next-hop address information based on the information in the IP routing table. Because there is a one-to-one correlation between FIB entries and routing table entries, the FIB contains all known routes and eliminates the need for route cache maintenance that is associated with earlier switching paths such as fast switching and optimum switching.
Note: In order to view the Routing information base (RIB) table, use the "show ip route" command.
To view the Forwarding Information Base (FIB), use the "show ip cef" command. RIB is in Control plane while FIB is in Data plane.
Cisco 350-401J - 今の社会の中で時間がそんなに重要で最も保障できるOmgzlookを選ばましょう。 CiscoのSAP C_THR85_2405試験に合格することは容易なことではなくて、良い訓練ツールは成功の保証でOmgzlookは君の試験の問題を準備してしまいました。 Microsoft AZ-500J - 今は時間がそんなに重要な社会でもっとも少ないお時間を使って試験に合格するのは一番よいだと思います。 ITの専門者はCiscoのFortinet FCP_FML_AD-7.4認定試験があなたの願望を助けって実現できるのがよく分かります。 Databricks Databricks-Certified-Professional-Data-Engineer - Omgzlookはまた一年間に無料なサービスを更新いたします。
Updated: May 28, 2022