弊社は350-401合格内容試験政策の変化に応じて、350-401合格内容試験資料を定期的に更新しています。こうした、お客様に全面的かつ高品質の350-401合格内容試験資料を提供できます。350-401合格内容試験に合格するために、お客様は今から350-401合格内容試験資料を手に入りましょう！ 試験問題と解答に関する質問があるなら、当社は直後に解決方法を差し上げます。しかも、一年間の無料更新サービスを提供します。 弊社の350-401合格内容復習教材は専門家によって編集されていました。
CCNP Enterprise 350-401 でも、成功へのショートカットがを見つけました。
CCNP Enterprise 350-401合格内容 - Implementing Cisco Enterprise Network Core Technologies (350-401 ENCOR) しかし必ずしも大量の時間とエネルギーで復習しなくて、弊社が丹精にできあがった問題集を使って、試験なんて問題ではありません。 きっと望んでいるでしょう。では、常に自分自身をアップグレードする必要があります。
弊社が提供した問題集がほかのインターネットに比べて問題のカーバ範囲がもっと広くて対応性が強い長所があります。Omgzlookが持つべきなIT問題集を提供するサイトでございます。
Cisco 350-401合格内容 - あなたに提供するソフトはその中の一部です。
OmgzlookのCiscoの350-401合格内容の試験問題は同じシラバスに従って、実際のCiscoの350-401合格内容認証試験にも従っています。弊社はずっとトレーニング資料をアップグレードしていますから、提供して差し上げた製品は一年間の無料更新サービスの景品があります。あなたはいつでもサブスクリプションの期間を延長することができますから、より多くの時間を取って充分に試験を準備できます。Omgzlookというサイトのトレーニング資料を利用するかどうかがまだ決まっていなかったら、Omgzlookのウェブで一部の試験問題と解答を無料にダウンローしてみることができます。あなたに向いていることを確かめてから買うのも遅くないですよ。あなたが決して後悔しないことを保証します。
Ciscoの350-401合格内容試験が更新するとともに我々の作成するソフトは更新しています。なぜ我々はあなたが購入した前にやってみることを許しますか。
350-401 PDF DEMO:
QUESTION NO: 1
To increase total throughput and redundancy on the links between the wireless controller and switch, the customer enabled LAG on the wireless controller.
Which EtherChannel mode must be configured on the switch to allow the WLC to connect?
A. Active
B. On
C. Auto
D. Passive
Answer: B
Explanation:
Restrictions for Link Aggregation:
You can bundle all eight ports on a Cisco 5508 Controller into a single link.
Terminating on two different modules within a single Catalyst 6500 series switch provides redundancy and ensures that connectivity between the switch and the controller is maintained when one module fails. The controller's port 1 is connected to Gigabit interface 3/1, and the controller's port 2 is connected to Gigabit interface 2/1 on the Catalyst 6500 series switch. Both switch ports are assigned to the same channel group.
LAG requires the EtherChannel to be configured for 'mode on' on both the controller and the Catalyst switch.
Once the EtherChannel is configured as on at both ends of the link, the Catalyst switch should not be configured for either Link Aggregation Control Protocol (LACP) or Cisco proprietary Port Aggregation
Protocol (PAgP) but be set unconditionally to LAG. Because no channel negotiation is done between the controller and the switch, the controller does not answer to negotiation frames and the LAG is not formed if a dynamic form of LAG is set on the switch. Additionally, LACP and PAgP are not supported on the controller.
If the recommended load-balancing method cannot be configured on the Catalyst switch, then configure the LAG connection as a single member link or disable LAG on the controller.
https://www.cisco.com/c/en/us/td/docs/wireless/controller/7-5/configuration- guide/b_cg75/b_cg75_chapter_0100010.html
QUESTION NO: 2
What is the difference between a RIB and a FIB?
A. The FIB is populated based on RIB content
B. The RIB is used to make IP source prefix-based switching decisions
C. The RIB maintains a mirror image of the FIB
D. The FIB is where all IP routing information is stored
Answer: A
Explanation:
CEF uses a Forwarding Information Base (FIB) to make IP destination prefix-based switching decisions.
The FIB is conceptually similar to a routing table or information base. It maintains a mirror image of the forwarding information contained in the IP routing table. When routing or topology changes occur in the network, the IP routing table is updated, and those changes are reflected in the FIB. The
FIB maintains next-hop address information based on the information in the IP routing table. Because there is a one-to-one correlation between FIB entries and routing table entries, the FIB contains all known routes and eliminates the need for route cache maintenance that is associated with earlier switching paths such as fast switching and optimum switching.
Note: In order to view the Routing information base (RIB) table, use the "show ip route" command.
To view the Forwarding Information Base (FIB), use the "show ip cef" command. RIB is in Control plane while FIB is in Data plane.
QUESTION NO: 3
Which technology provides a secure communication channel for all traffic at Layer 2 of the OSI model?
A. IPsec
B. Cisco Trustsec
C. MACsec
D. SSL
Answer: C
Explanation:
MACsec, defined in 802.1AE, provides MAC-layer encryption over wired networks by using out- of
-band methods for encryption keying. The MACsec Key Agreement (MKA) Protocol provides the required session keys and manages the required encryption keys. MKA and MACsec are implemented after successful authentication using the 802.1x Extensible Authentication Protocol (EAP-TLS) or Pre
Shared Key (PSK) framework.
A switch using MACsec accepts either MACsec or non-MACsec frames, depending on the policy associated with the MKA peer. MACsec frames are encrypted and protected with an integrity check value (ICV). When the switch receives frames from the MKA peer, it decrypts them and calculates the correct ICV by using session keys provided by MKA. The switch compares that ICV to the ICV within the frame. If they are not identical, the frame is dropped. The switch also encrypts and adds an ICV to any frames sent over the secured port (the access point used to provide the secure MAC service to a
MKA peer) using the current session key.
Reference: https://www.cisco.com/c/en/us/td/docs/switches/lan/catalyst9300/software/release/16-
9/configuration_guide/sec/b_169_sec_9300_cg/macsec_encryption.html
Note: Cisco Trustsec is the solution which includes MACsec.
QUESTION NO: 4
Refer to the exhibit. A port channel is configured between SW2 and SW3. SW2 is not running a
Cisco operating system. When all physical connections are mode, the port channel does not establish.
Based on the configuration excerpt of SW3, what is the cause of the problem?
A. The port-channel interface lead balance should be set to src-mac
B. The port-channel trunk is not allowing the native VLAN.
C. The port-channel should be set to auto.
D. The port channel on SW2 is using an incompatible protocol.
Answer: D
Explanation:
The Cisco switch was configured with PAgP, which is a Cisco proprietary protocol so non-Cisco switch could not communicate.
QUESTION NO: 5
Which feature does Cisco TrustSec use to provide scalable, secure communication throughout a network?
A. security group tag number assigned to each user on a switch
B. security group tag ACL assigned to each router on a network
C. security group tag ACL assigned to each port on a switch
D. security group tag number assigned to each port on a network
Answer: D
Explanation:
Cisco TrustSec uses tags to represent logical group privilege. This tag, called a Security Group Tag
(SGT), is used in access policies. The SGT is understood and is used to enforce traffic by Cisco switches, routers and firewalls . Cisco TrustSec is defined in three phases: classification, propagation and enforcement.
When users and devices connect to a network, the network assigns a specific security group.
This process is called classification. Classification can be based on the results of the authentication or by associating the SGT with an IP, VLAN, or port-profile (-> Answer A and answer C are not correct as they say "assigned ... on a switch" only. Answer D is not correct either as it says "assigned to each router").
CiscoのEMC D-NWG-DS-00認定試験に受かるのはあなたの技能を検証することだけでなく、あなたの専門知識を証明できて、上司は無駄にあなたを雇うことはしないことの証明書です。 CiscoのMicrosoft AZ-140J試験に失敗しても、我々はあなたの経済損失を減少するために全額で返金します。 Omgzlookの試験トレーニング資料はCiscoのScaled Agile SAFe-APM認定試験の１００パーセントの合格率を保証します。 我が社のCiscoのSailPoint IdentityIQ-Engineer習題を勉強して、最も良い結果を得ることができます。 SAP C-THR88-2405 - Omgzlookで、あなたの試験のためのテクニックと勉強資料を見つけることができます。
Updated: May 28, 2022