ここで無料にOmgzlookが提供したCiscoの350-401受験対策解説集試験の部分練習問題と解答をダウンロードできて、一度Omgzlookを選ばれば、弊社は全力に貴方達の合格を頑張ります。貴方達の試験に合格させることができないと、すぐに全額で返金いたします。 もちろん、我々はあなたに一番安心させるのは我々の開発する多くの受験生に合格させるCiscoの350-401受験対策解説集試験のソフトウェアです。我々はあなたに提供するのは最新で一番全面的なCiscoの350-401受験対策解説集問題集で、最も安全な購入保障で、最もタイムリーなCiscoの350-401受験対策解説集試験のソフトウェアの更新です。 たくさんのひとは弊社の商品を使って、試験に順調に合格しました。
CCNP Enterprise 350-401 もし合格しないと、われは全額で返金いたします。
CCNP Enterprise 350-401受験対策解説集 - Implementing Cisco Enterprise Network Core Technologies (350-401 ENCOR) 成功したいのですか。 Cisco 350-401 試験資料「Implementing Cisco Enterprise Network Core Technologies (350-401 ENCOR)」認証試験に合格することが簡単ではなくて、Cisco 350-401 試験資料証明書は君にとってはIT業界に入るの一つの手づるになるかもしれません。しかし必ずしも大量の時間とエネルギーで復習しなくて、弊社が丹精にできあがった問題集を使って、試験なんて問題ではありません。
誰もが成功する可能性があって、大切なのは選択することです。成功した方法を見つけるだけで、失敗の言い訳をしないでください。Ciscoの350-401受験対策解説集試験に受かるのは実際にそんなに難しいことではないです。
Cisco 350-401受験対策解説集 - IT認定試験は様々あります。
Ciscoの350-401受験対策解説集認定試験は実は技術専門家を認証する試験です。 Ciscoの350-401受験対策解説集認定試験はIT人員が優れたキャリアを持つことを助けられます。優れたキャリアを持ったら、社会と国のために色々な利益を作ることができて、国の経済が継続的に発展していることを進められるようになります。全てのIT人員がそんなにられるとしたら、国はぜひ強くなります。OmgzlookのCiscoの350-401受験対策解説集試験トレーニング資料はIT人員の皆さんがそんな目標を達成できるようにヘルプを提供して差し上げます。OmgzlookのCiscoの350-401受験対策解説集試験トレーニング資料は１００パーセントの合格率を保証しますから、ためらわずに決断してOmgzlookを選びましょう。
非常に人気があるCiscoの認定試験の一つとして、この試験も大切です。しかし、試験の準備をよりよくできるために試験参考書を探しているときに、優秀な参考資料を見つけるのはたいへん難しいことがわかります。
350-401 PDF DEMO:
QUESTION NO: 1
Refer to the exhibit. A port channel is configured between SW2 and SW3. SW2 is not running a
Cisco operating system. When all physical connections are mode, the port channel does not establish.
Based on the configuration excerpt of SW3, what is the cause of the problem?
A. The port-channel interface lead balance should be set to src-mac
B. The port-channel trunk is not allowing the native VLAN.
C. The port-channel should be set to auto.
D. The port channel on SW2 is using an incompatible protocol.
Answer: D
Explanation:
The Cisco switch was configured with PAgP, which is a Cisco proprietary protocol so non-Cisco switch could not communicate.
QUESTION NO: 2
Which statement about multicast RPs is true?
A. RPs are required for protocol independent multicast sparse mode and dense mode.
B. By default, the RP is needed only to start new sessions with sources and receivers.
C. By default, the RP is needed periodically to maintain sessions with sources and receivers
D. RPs are required only when using protocol independent multicast dense mode.
Answer: B
Explanation:
A rendezvous point (RP) is required only in networks running Protocol Independent Multicast sparse mode (PIM-SM).
By default, the RP is needed only to start new sessions with sources and receivers.
Reference:
https://www.cisco.com/c/en/us/td/docs/ios/solutions_docs/ip_multicast/White_papers/rps.html
For your information, in PIM-SM, only network segments with active receivers that have explicitly requested multicast data will be forwarded the traffic. This method of delivering multicast data is in contrast to the PIM dense mode (PIM-DM) model. In PIM-DM, multicast traffic is initially flooded to all segments of the network. Routers that have no downstream neighbors or directly connected receivers prune back the unwanted traffic.
QUESTION NO: 3
Which technology provides a secure communication channel for all traffic at Layer 2 of the OSI model?
A. IPsec
B. Cisco Trustsec
C. MACsec
D. SSL
Answer: C
Explanation:
MACsec, defined in 802.1AE, provides MAC-layer encryption over wired networks by using out- of
-band methods for encryption keying. The MACsec Key Agreement (MKA) Protocol provides the required session keys and manages the required encryption keys. MKA and MACsec are implemented after successful authentication using the 802.1x Extensible Authentication Protocol (EAP-TLS) or Pre
Shared Key (PSK) framework.
A switch using MACsec accepts either MACsec or non-MACsec frames, depending on the policy associated with the MKA peer. MACsec frames are encrypted and protected with an integrity check value (ICV). When the switch receives frames from the MKA peer, it decrypts them and calculates the correct ICV by using session keys provided by MKA. The switch compares that ICV to the ICV within the frame. If they are not identical, the frame is dropped. The switch also encrypts and adds an ICV to any frames sent over the secured port (the access point used to provide the secure MAC service to a
MKA peer) using the current session key.
Reference: https://www.cisco.com/c/en/us/td/docs/switches/lan/catalyst9300/software/release/16-
9/configuration_guide/sec/b_169_sec_9300_cg/macsec_encryption.html
Note: Cisco Trustsec is the solution which includes MACsec.
QUESTION NO: 4
Which access controls list allows only TCP traffic with a destination port range of 22-433, excluding port 80?
A. Deny tcp any any ne 80
Permit tcp any any range 22 443
B. Permit tcp any any ne 80
C. Permit tco any any range 22 443
Deny tcp any any eq 80
D. Deny tcp any any eq 80
Permit tco any any gt 21 it 444
Answer: D
QUESTION NO: 5
To increase total throughput and redundancy on the links between the wireless controller and switch, the customer enabled LAG on the wireless controller.
Which EtherChannel mode must be configured on the switch to allow the WLC to connect?
A. Active
B. On
C. Auto
D. Passive
Answer: B
Explanation:
Restrictions for Link Aggregation:
You can bundle all eight ports on a Cisco 5508 Controller into a single link.
Terminating on two different modules within a single Catalyst 6500 series switch provides redundancy and ensures that connectivity between the switch and the controller is maintained when one module fails. The controller's port 1 is connected to Gigabit interface 3/1, and the controller's port 2 is connected to Gigabit interface 2/1 on the Catalyst 6500 series switch. Both switch ports are assigned to the same channel group.
LAG requires the EtherChannel to be configured for 'mode on' on both the controller and the Catalyst switch.
Once the EtherChannel is configured as on at both ends of the link, the Catalyst switch should not be configured for either Link Aggregation Control Protocol (LACP) or Cisco proprietary Port Aggregation
Protocol (PAgP) but be set unconditionally to LAG. Because no channel negotiation is done between the controller and the switch, the controller does not answer to negotiation frames and the LAG is not formed if a dynamic form of LAG is set on the switch. Additionally, LACP and PAgP are not supported on the controller.
If the recommended load-balancing method cannot be configured on the Catalyst switch, then configure the LAG connection as a single member link or disable LAG on the controller.
https://www.cisco.com/c/en/us/td/docs/wireless/controller/7-5/configuration- guide/b_cg75/b_cg75_chapter_0100010.html
VMware 3V0-61.24 - 」とゴーリキーは述べました。 OmgzlookはCiscoのQlik QREP問題集の正確性と高いカバー率を保証します。 VMware 3V0-31.24 - あなたの夢は何ですか。 EMC D-SF-A-24 - Omgzlookを選ぶなら、私たちは君の認定試験に合格するのを保証します。 OmgzlookのAPI API-510教材を購入したら、あなたは一年間の無料アップデートサービスを取得しました。
Updated: May 28, 2022