この二つのバージョンを利用して、受験生の皆さんは試験の準備をするときにもっと楽になることができます。Omgzlookの350-401勉強方法問題集を利用してみたらどうですか。この問題集は350-401勉強方法試験に関連するすべての参考書の中で一番優秀なものだと言えます。 暇の時間を利用して勉強します。努力すれば報われますなので、Cisco 350-401勉強方法資格認定を取得して自分の生活状況を改善できます。 もし君はいささかな心配することがあるなら、あなたはうちの商品を購入する前に、Omgzlookは無料でサンプルを提供することができます。
CCNP Enterprise 350-401 素晴らしい試験参考書です。
IT認定試験の中でどんな試験を受けても、Omgzlookの350-401 - Implementing Cisco Enterprise Network Core Technologies (350-401 ENCOR)勉強方法試験参考資料はあなたに大きなヘルプを与えることができます。 弊社は強力な教師チームがあって、彼たちは正確ではやくて例年のCisco 350-401 復習内容認定試験の資料を整理して、直ちにもっとも最新の資料を集めて、弊社は全会一緻で認められています。Cisco 350-401 復習内容試験認証に合格確率はとても小さいですが、Omgzlookはその合格確率を高めることが信じてくだい。
その中で、350-401勉強方法認定試験は最も重要な一つです。では、この試験に合格するためにどのように試験の準備をしているのですか。がむしゃらに試験に関連する知識を勉強しているのですか。
Cisco 350-401勉強方法 - 」とゴーリキーは述べました。
OmgzlookのCiscoの350-401勉強方法試験トレーニング資料はIT認証試験を受ける全ての受験生が試験に合格することを助けるもので、受験生からの良い評価をたくさんもらいました。Omgzlookを選ぶのは成功を選ぶのに等しいです。もしOmgzlookのCiscoの350-401勉強方法試験トレーニング資料を購入した後、学習教材は問題があれば、或いは試験に不合格になる場合は、私たちが全額返金することを保証いたしますし、私たちは一年間で無料更新サービスを提供することもできます。
きっと望んでいるでしょう。では、常に自分自身をアップグレードする必要があります。
350-401 PDF DEMO:
QUESTION NO: 1
What is the difference between a RIB and a FIB?
A. The FIB is populated based on RIB content
B. The RIB is used to make IP source prefix-based switching decisions
C. The RIB maintains a mirror image of the FIB
D. The FIB is where all IP routing information is stored
Answer: A
Explanation:
CEF uses a Forwarding Information Base (FIB) to make IP destination prefix-based switching decisions.
The FIB is conceptually similar to a routing table or information base. It maintains a mirror image of the forwarding information contained in the IP routing table. When routing or topology changes occur in the network, the IP routing table is updated, and those changes are reflected in the FIB. The
FIB maintains next-hop address information based on the information in the IP routing table. Because there is a one-to-one correlation between FIB entries and routing table entries, the FIB contains all known routes and eliminates the need for route cache maintenance that is associated with earlier switching paths such as fast switching and optimum switching.
Note: In order to view the Routing information base (RIB) table, use the "show ip route" command.
To view the Forwarding Information Base (FIB), use the "show ip cef" command. RIB is in Control plane while FIB is in Data plane.
QUESTION NO: 2
Which feature does Cisco TrustSec use to provide scalable, secure communication throughout a network?
A. security group tag number assigned to each user on a switch
B. security group tag ACL assigned to each router on a network
C. security group tag ACL assigned to each port on a switch
D. security group tag number assigned to each port on a network
Answer: D
Explanation:
Cisco TrustSec uses tags to represent logical group privilege. This tag, called a Security Group Tag
(SGT), is used in access policies. The SGT is understood and is used to enforce traffic by Cisco switches, routers and firewalls . Cisco TrustSec is defined in three phases: classification, propagation and enforcement.
When users and devices connect to a network, the network assigns a specific security group.
This process is called classification. Classification can be based on the results of the authentication or by associating the SGT with an IP, VLAN, or port-profile (-> Answer A and answer C are not correct as they say "assigned ... on a switch" only. Answer D is not correct either as it says "assigned to each router").
QUESTION NO: 3
To increase total throughput and redundancy on the links between the wireless controller and switch, the customer enabled LAG on the wireless controller.
Which EtherChannel mode must be configured on the switch to allow the WLC to connect?
A. Active
B. On
C. Auto
D. Passive
Answer: B
Explanation:
Restrictions for Link Aggregation:
You can bundle all eight ports on a Cisco 5508 Controller into a single link.
Terminating on two different modules within a single Catalyst 6500 series switch provides redundancy and ensures that connectivity between the switch and the controller is maintained when one module fails. The controller's port 1 is connected to Gigabit interface 3/1, and the controller's port 2 is connected to Gigabit interface 2/1 on the Catalyst 6500 series switch. Both switch ports are assigned to the same channel group.
LAG requires the EtherChannel to be configured for 'mode on' on both the controller and the Catalyst switch.
Once the EtherChannel is configured as on at both ends of the link, the Catalyst switch should not be configured for either Link Aggregation Control Protocol (LACP) or Cisco proprietary Port Aggregation
Protocol (PAgP) but be set unconditionally to LAG. Because no channel negotiation is done between the controller and the switch, the controller does not answer to negotiation frames and the LAG is not formed if a dynamic form of LAG is set on the switch. Additionally, LACP and PAgP are not supported on the controller.
If the recommended load-balancing method cannot be configured on the Catalyst switch, then configure the LAG connection as a single member link or disable LAG on the controller.
https://www.cisco.com/c/en/us/td/docs/wireless/controller/7-5/configuration- guide/b_cg75/b_cg75_chapter_0100010.html
QUESTION NO: 4
Which technology provides a secure communication channel for all traffic at Layer 2 of the OSI model?
A. IPsec
B. Cisco Trustsec
C. MACsec
D. SSL
Answer: C
Explanation:
MACsec, defined in 802.1AE, provides MAC-layer encryption over wired networks by using out- of
-band methods for encryption keying. The MACsec Key Agreement (MKA) Protocol provides the required session keys and manages the required encryption keys. MKA and MACsec are implemented after successful authentication using the 802.1x Extensible Authentication Protocol (EAP-TLS) or Pre
Shared Key (PSK) framework.
A switch using MACsec accepts either MACsec or non-MACsec frames, depending on the policy associated with the MKA peer. MACsec frames are encrypted and protected with an integrity check value (ICV). When the switch receives frames from the MKA peer, it decrypts them and calculates the correct ICV by using session keys provided by MKA. The switch compares that ICV to the ICV within the frame. If they are not identical, the frame is dropped. The switch also encrypts and adds an ICV to any frames sent over the secured port (the access point used to provide the secure MAC service to a
MKA peer) using the current session key.
Reference: https://www.cisco.com/c/en/us/td/docs/switches/lan/catalyst9300/software/release/16-
9/configuration_guide/sec/b_169_sec_9300_cg/macsec_encryption.html
Note: Cisco Trustsec is the solution which includes MACsec.
QUESTION NO: 5
Refer to the exhibit. A port channel is configured between SW2 and SW3. SW2 is not running a
Cisco operating system. When all physical connections are mode, the port channel does not establish.
Based on the configuration excerpt of SW3, what is the cause of the problem?
A. The port-channel interface lead balance should be set to src-mac
B. The port-channel trunk is not allowing the native VLAN.
C. The port-channel should be set to auto.
D. The port channel on SW2 is using an incompatible protocol.
Answer: D
Explanation:
The Cisco switch was configured with PAgP, which is a Cisco proprietary protocol so non-Cisco switch could not communicate.
あなたの利用するCiscoのMicrosoft DP-203Jソフトが最新版のを保証するために、一年間の無料更新を提供します。 OmgzlookのIBM C1000-112教材を購入したら、あなたは一年間の無料アップデートサービスを取得しました。 CiscoのSAP C_ARCIG_2404試験はいくつ難しくても文句を言わないで、我々Omgzlookの提供する資料を通して、あなたはCiscoのSAP C_ARCIG_2404試験に合格することができます。 Omgzlookのウェブサイトに行ってもっとたくさんの情報をブラウズして、あなたがほしい試験Cisco 500-490参考書を見つけてください。 あなたに安心にネットでCiscoのGoogle Professional-Cloud-Network-Engineer-JPN試験の資料を購入させるために、我々Omgzlookは国際の最大の安全的な支払システムPaypalと協力してあなたの支払の安全性を保障します。
Updated: May 28, 2022