あなたはいつまでも最新版の問題集を使用できるために、ご購入の一年間で無料の更新を提供します。人によって目標が違いますが、あなたにCisco 350-401テスト対策書試験に順調に合格できるのは我々の共同の目標です。この目標の達成はあなたがIT技術領域へ行く更なる発展の一歩ですけど、我々社Omgzlook存在するこそすべての意義です。 Ciscoの350-401テスト対策書認定試験に受かるのはあなたの技能を検証することだけでなく、あなたの専門知識を証明できて、上司は無駄にあなたを雇うことはしないことの証明書です。当面、IT業界でCiscoの350-401テスト対策書認定試験の信頼できるソースが必要です。 もし、あなたも350-401テスト対策書問題集を購入すれば、試験に合格できますよ。
そのデモは350-401テスト対策書試験資料の一部を含めています。
OmgzlookのCiscoの350-401 - Implementing Cisco Enterprise Network Core Technologies (350-401 ENCOR)テスト対策書試験トレーニング資料を持っていたら、試験に対する充分の準備がありますから、安心に利用したください。 Ciscoの350-401 テスト模擬問題集の認定試験に合格すれば、就職機会が多くなります。OmgzlookはCiscoの350-401 テスト模擬問題集の認定試験の受験生にとっても適合するサイトで、受験生に試験に関する情報を提供するだけでなく、試験の問題と解答をはっきり解説いたします。
これは試験の準備をするために非常に効率的なツールですから。この問題集はあなたが少ない労力で最高の結果を取得することができます。OmgzlookはIT認定試験を受験した多くの人々を助けました。
Cisco 350-401テスト対策書 - 何の問題があったらお気軽に聞いてください。
時間とお金の集まりより正しい方法がもっと大切です。Ciscoの350-401テスト対策書試験のために勉強していますなら、Omgzlookの提供するCiscoの350-401テスト対策書試験ソフトはあなたの選びの最高です。我々の目的はあなたにCiscoの350-401テスト対策書試験に合格することだけです。試験に失敗したら、弊社は全額で返金します。我々の誠意を信じてください。あなたが順調に試験に合格するように。
現在でCiscoの350-401テスト対策書試験を受かることができます。OmgzlookにCiscoの350-401テスト対策書試験のフルバージョンがありますから、最新のCiscoの350-401テスト対策書のトレーニング資料をあちこち探す必要がないです。
350-401 PDF DEMO:
QUESTION NO: 1
To increase total throughput and redundancy on the links between the wireless controller and switch, the customer enabled LAG on the wireless controller.
Which EtherChannel mode must be configured on the switch to allow the WLC to connect?
A. Active
B. On
C. Auto
D. Passive
Answer: B
Explanation:
Restrictions for Link Aggregation:
You can bundle all eight ports on a Cisco 5508 Controller into a single link.
Terminating on two different modules within a single Catalyst 6500 series switch provides redundancy and ensures that connectivity between the switch and the controller is maintained when one module fails. The controller's port 1 is connected to Gigabit interface 3/1, and the controller's port 2 is connected to Gigabit interface 2/1 on the Catalyst 6500 series switch. Both switch ports are assigned to the same channel group.
LAG requires the EtherChannel to be configured for 'mode on' on both the controller and the Catalyst switch.
Once the EtherChannel is configured as on at both ends of the link, the Catalyst switch should not be configured for either Link Aggregation Control Protocol (LACP) or Cisco proprietary Port Aggregation
Protocol (PAgP) but be set unconditionally to LAG. Because no channel negotiation is done between the controller and the switch, the controller does not answer to negotiation frames and the LAG is not formed if a dynamic form of LAG is set on the switch. Additionally, LACP and PAgP are not supported on the controller.
If the recommended load-balancing method cannot be configured on the Catalyst switch, then configure the LAG connection as a single member link or disable LAG on the controller.
https://www.cisco.com/c/en/us/td/docs/wireless/controller/7-5/configuration- guide/b_cg75/b_cg75_chapter_0100010.html
QUESTION NO: 2
What is the difference between a RIB and a FIB?
A. The FIB is populated based on RIB content
B. The RIB is used to make IP source prefix-based switching decisions
C. The RIB maintains a mirror image of the FIB
D. The FIB is where all IP routing information is stored
Answer: A
Explanation:
CEF uses a Forwarding Information Base (FIB) to make IP destination prefix-based switching decisions.
The FIB is conceptually similar to a routing table or information base. It maintains a mirror image of the forwarding information contained in the IP routing table. When routing or topology changes occur in the network, the IP routing table is updated, and those changes are reflected in the FIB. The
FIB maintains next-hop address information based on the information in the IP routing table. Because there is a one-to-one correlation between FIB entries and routing table entries, the FIB contains all known routes and eliminates the need for route cache maintenance that is associated with earlier switching paths such as fast switching and optimum switching.
Note: In order to view the Routing information base (RIB) table, use the "show ip route" command.
To view the Forwarding Information Base (FIB), use the "show ip cef" command. RIB is in Control plane while FIB is in Data plane.
QUESTION NO: 3
Which technology provides a secure communication channel for all traffic at Layer 2 of the OSI model?
A. IPsec
B. Cisco Trustsec
C. MACsec
D. SSL
Answer: C
Explanation:
MACsec, defined in 802.1AE, provides MAC-layer encryption over wired networks by using out- of
-band methods for encryption keying. The MACsec Key Agreement (MKA) Protocol provides the required session keys and manages the required encryption keys. MKA and MACsec are implemented after successful authentication using the 802.1x Extensible Authentication Protocol (EAP-TLS) or Pre
Shared Key (PSK) framework.
A switch using MACsec accepts either MACsec or non-MACsec frames, depending on the policy associated with the MKA peer. MACsec frames are encrypted and protected with an integrity check value (ICV). When the switch receives frames from the MKA peer, it decrypts them and calculates the correct ICV by using session keys provided by MKA. The switch compares that ICV to the ICV within the frame. If they are not identical, the frame is dropped. The switch also encrypts and adds an ICV to any frames sent over the secured port (the access point used to provide the secure MAC service to a
MKA peer) using the current session key.
Reference: https://www.cisco.com/c/en/us/td/docs/switches/lan/catalyst9300/software/release/16-
9/configuration_guide/sec/b_169_sec_9300_cg/macsec_encryption.html
Note: Cisco Trustsec is the solution which includes MACsec.
QUESTION NO: 4
Refer to the exhibit. A port channel is configured between SW2 and SW3. SW2 is not running a
Cisco operating system. When all physical connections are mode, the port channel does not establish.
Based on the configuration excerpt of SW3, what is the cause of the problem?
A. The port-channel interface lead balance should be set to src-mac
B. The port-channel trunk is not allowing the native VLAN.
C. The port-channel should be set to auto.
D. The port channel on SW2 is using an incompatible protocol.
Answer: D
Explanation:
The Cisco switch was configured with PAgP, which is a Cisco proprietary protocol so non-Cisco switch could not communicate.
QUESTION NO: 5
Which feature does Cisco TrustSec use to provide scalable, secure communication throughout a network?
A. security group tag number assigned to each user on a switch
B. security group tag ACL assigned to each router on a network
C. security group tag ACL assigned to each port on a switch
D. security group tag number assigned to each port on a network
Answer: D
Explanation:
Cisco TrustSec uses tags to represent logical group privilege. This tag, called a Security Group Tag
(SGT), is used in access policies. The SGT is understood and is used to enforce traffic by Cisco switches, routers and firewalls . Cisco TrustSec is defined in three phases: classification, propagation and enforcement.
When users and devices connect to a network, the network assigns a specific security group.
This process is called classification. Classification can be based on the results of the authentication or by associating the SGT with an IP, VLAN, or port-profile (-> Answer A and answer C are not correct as they say "assigned ... on a switch" only. Answer D is not correct either as it says "assigned to each router").
CiscoのMicrosoft AZ-104試験を準備しているあなたに試験に合格させるために、我々Omgzlookは模擬試験ソフトを更新し続けています。 ISC SSCP-JPN - この認証は自分のキャリアを強化することができ、自分が成功に近づかせますから。 あなたは自分の望ましいCisco Juniper JN0-223問題集を選らんで、学びから更なる成長を求められます。 Salesforce Sales-Cloud-Consultant-JPN - 彼らは当社の資料を利用してから試験に受かりました。 現在IT技術会社に通勤しているあなたは、CiscoのPECB ISO-IEC-27001-Lead-Auditor-KR試験認定を取得しましたか？PECB ISO-IEC-27001-Lead-Auditor-KR試験認定は給料の増加とジョブのプロモーションに役立ちます。
Updated: May 28, 2022