Omgzlookはきみの貴重な時間を節約するだけでなく、 安心で順調に試験に合格するのを保証します。Omgzlookは専門のIT業界での評判が高くて、あなたがインターネットでOmgzlookの部分のCisco 350-401サンプル問題集「Implementing Cisco Enterprise Network Core Technologies (350-401 ENCOR)」資料を無料でダウンロードして、弊社の正確率を確認してください。弊社の商品が好きなのは弊社のたのしいです。 Omgzlookは広い研究と実際を基づいている経験及び正確的な学習教材を提供できます。私たちは君の最も早い時間でCiscoの350-401サンプル問題集試験に合格するように頑張ります。 Omgzlook を選択して１００％の合格率を確保することができて、もし試験に失敗したら、Omgzlookが全額で返金いたします。
CCNP Enterprise 350-401 Omgzlookを選んだ方が良いです。
あなたはインターネットでCiscoの350-401 - Implementing Cisco Enterprise Network Core Technologies (350-401 ENCOR)サンプル問題集認証試験の練習問題と解答の試用版を無料でダウンロードしてください。 Omgzlookの Ciscoの350-401 過去問無料試験トレーニング資料は高度に認証されたIT領域の専門家の経験と創造を含めているものです。それは正確性が高くて、カバー率も広いです。
OmgzlookにIT業界のエリートのグループがあって、彼達は自分の経験と専門知識を使ってCisco 350-401サンプル問題集認証試験に参加する方に対して問題集を研究続けています。君が後悔しないようにもっと少ないお金を使って大きな良い成果を取得するためにOmgzlookを選択してください。Omgzlookはまた一年間に無料なサービスを更新いたします。
Cisco 350-401サンプル問題集 - Omgzlookを選んだら、成功への扉を開きます。
今の社会では、高い効率の仕方を慣れんでいます。あなたはCiscoの350-401サンプル問題集資格認定のために、他人より多くの時間をかかるんですか？Omgzlookの350-401サンプル問題集問題集を紹介させてください。350-401サンプル問題集は専門家たちが長年の経験で研究分析した勉強資料です。受験生のあなたを助けて時間とお金を節約したり、350-401サンプル問題集試験に速く合格すると保証します。
問題が更新される限り、Omgzlookは直ちに最新版の350-401サンプル問題集資料を送ってあげます。そうすると、あなたがいつでも最新バージョンの資料を持っていることが保証されます。
350-401 PDF DEMO:
QUESTION NO: 1
Which technology provides a secure communication channel for all traffic at Layer 2 of the OSI model?
A. IPsec
B. Cisco Trustsec
C. MACsec
D. SSL
Answer: C
Explanation:
MACsec, defined in 802.1AE, provides MAC-layer encryption over wired networks by using out- of
-band methods for encryption keying. The MACsec Key Agreement (MKA) Protocol provides the required session keys and manages the required encryption keys. MKA and MACsec are implemented after successful authentication using the 802.1x Extensible Authentication Protocol (EAP-TLS) or Pre
Shared Key (PSK) framework.
A switch using MACsec accepts either MACsec or non-MACsec frames, depending on the policy associated with the MKA peer. MACsec frames are encrypted and protected with an integrity check value (ICV). When the switch receives frames from the MKA peer, it decrypts them and calculates the correct ICV by using session keys provided by MKA. The switch compares that ICV to the ICV within the frame. If they are not identical, the frame is dropped. The switch also encrypts and adds an ICV to any frames sent over the secured port (the access point used to provide the secure MAC service to a
MKA peer) using the current session key.
Reference: https://www.cisco.com/c/en/us/td/docs/switches/lan/catalyst9300/software/release/16-
9/configuration_guide/sec/b_169_sec_9300_cg/macsec_encryption.html
Note: Cisco Trustsec is the solution which includes MACsec.
QUESTION NO: 2
Refer to the exhibit. A port channel is configured between SW2 and SW3. SW2 is not running a
Cisco operating system. When all physical connections are mode, the port channel does not establish.
Based on the configuration excerpt of SW3, what is the cause of the problem?
A. The port-channel interface lead balance should be set to src-mac
B. The port-channel trunk is not allowing the native VLAN.
C. The port-channel should be set to auto.
D. The port channel on SW2 is using an incompatible protocol.
Answer: D
Explanation:
The Cisco switch was configured with PAgP, which is a Cisco proprietary protocol so non-Cisco switch could not communicate.
QUESTION NO: 3
To increase total throughput and redundancy on the links between the wireless controller and switch, the customer enabled LAG on the wireless controller.
Which EtherChannel mode must be configured on the switch to allow the WLC to connect?
A. Active
B. On
C. Auto
D. Passive
Answer: B
Explanation:
Restrictions for Link Aggregation:
You can bundle all eight ports on a Cisco 5508 Controller into a single link.
Terminating on two different modules within a single Catalyst 6500 series switch provides redundancy and ensures that connectivity between the switch and the controller is maintained when one module fails. The controller's port 1 is connected to Gigabit interface 3/1, and the controller's port 2 is connected to Gigabit interface 2/1 on the Catalyst 6500 series switch. Both switch ports are assigned to the same channel group.
LAG requires the EtherChannel to be configured for 'mode on' on both the controller and the Catalyst switch.
Once the EtherChannel is configured as on at both ends of the link, the Catalyst switch should not be configured for either Link Aggregation Control Protocol (LACP) or Cisco proprietary Port Aggregation
Protocol (PAgP) but be set unconditionally to LAG. Because no channel negotiation is done between the controller and the switch, the controller does not answer to negotiation frames and the LAG is not formed if a dynamic form of LAG is set on the switch. Additionally, LACP and PAgP are not supported on the controller.
If the recommended load-balancing method cannot be configured on the Catalyst switch, then configure the LAG connection as a single member link or disable LAG on the controller.
https://www.cisco.com/c/en/us/td/docs/wireless/controller/7-5/configuration- guide/b_cg75/b_cg75_chapter_0100010.html
QUESTION NO: 4
Which statement about multicast RPs is true?
A. RPs are required for protocol independent multicast sparse mode and dense mode.
B. By default, the RP is needed only to start new sessions with sources and receivers.
C. By default, the RP is needed periodically to maintain sessions with sources and receivers
D. RPs are required only when using protocol independent multicast dense mode.
Answer: B
Explanation:
A rendezvous point (RP) is required only in networks running Protocol Independent Multicast sparse mode (PIM-SM).
By default, the RP is needed only to start new sessions with sources and receivers.
Reference:
https://www.cisco.com/c/en/us/td/docs/ios/solutions_docs/ip_multicast/White_papers/rps.html
For your information, in PIM-SM, only network segments with active receivers that have explicitly requested multicast data will be forwarded the traffic. This method of delivering multicast data is in contrast to the PIM dense mode (PIM-DM) model. In PIM-DM, multicast traffic is initially flooded to all segments of the network. Routers that have no downstream neighbors or directly connected receivers prune back the unwanted traffic.
QUESTION NO: 5
What is the difference between a RIB and a FIB?
A. The FIB is populated based on RIB content
B. The RIB is used to make IP source prefix-based switching decisions
C. The RIB maintains a mirror image of the FIB
D. The FIB is where all IP routing information is stored
Answer: A
Explanation:
CEF uses a Forwarding Information Base (FIB) to make IP destination prefix-based switching decisions.
The FIB is conceptually similar to a routing table or information base. It maintains a mirror image of the forwarding information contained in the IP routing table. When routing or topology changes occur in the network, the IP routing table is updated, and those changes are reflected in the FIB. The
FIB maintains next-hop address information based on the information in the IP routing table. Because there is a one-to-one correlation between FIB entries and routing table entries, the FIB contains all known routes and eliminates the need for route cache maintenance that is associated with earlier switching paths such as fast switching and optimum switching.
Note: In order to view the Routing information base (RIB) table, use the "show ip route" command.
To view the Forwarding Information Base (FIB), use the "show ip cef" command. RIB is in Control plane while FIB is in Data plane.
これなので、IT技術職員としてのあなたはOmgzlookのCisco Microsoft AI-102J問題集デモを参考し、試験の準備に速く行動しましょう。 あるいは、無料で試験SAP C-HRHPC-2405問題集を更新してあげるのを選択することもできます。 しかし、幸いにして、SAP C-THR87-2405の練習問題の専門会社として、弊社の最も正確な質問と回答を含むSAP C-THR87-2405試験の資料は、SAP C-THR87-2405試験対する問題を効果的に解決できます。 Huawei H19-315 - なぜ受験生のほとんどはOmgzlookを選んだのですか。 Cisco 700-805 - 絶対見逃さないです。
Updated: May 28, 2022